
CSA Z259.2.4:15 (R2025)
CSA Z259.2.4:15 (R2025) – Fall arresters and vertical rigid rails
CDN $181.00
Fall arresters and vertical rigid rails
Description
Preface This is the second edition of CSA Z259.2.4, Fall arresters and vertical rigid rails . It is part of a series of Standards on components of fall-protection systems and replaces the previous edition published in 2012. This Standard is considered suitable for use for conformity assessment within the stated scope of the Standard. CSA gratefully acknowledges the financial and in-kind support from the Canadian government departments responsible for occupational health and safety for the development of this edition. This Standard was prepared by the Subcommittee on Fall Arresters and Vertical Rigid Rails, under the jurisdiction of the Technical Committee on Fall Protection and the Strategic Steering Committee on Occupational Health and Safety, and has been formally approved by the Technical Committee. Scope 1.1 This Standard specifies design, testing, and marking requirements for manufactured fall arresters and fixed vertical rigid rails that are used on a vertical or sloped plane. 1.2 The equipment specified in this Standard is intended for use where there is a danger of falling from heights. In the event of fall, the fall arrester will lock on the fixed vertical rigid rail to arrest the fall. 1.3 This Standard does not cover work positioning and horizontal travel systems. 1.4 The values given in SI units are the units of record for the purposes of this Standard. The values given in parentheses are for information and comparison only. 1.5 In this Standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the Standard. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.
Edition
Not found
Published Date
2026-10-05
Status
Not found
Pages
30
Format 
Secure PDF
Secure – PDF details
- Save your file locally or view it via a web viewer
- Viewing permissions are restricted exclusively to the purchaser
- Device limits - 3
- Printing – Enabled only to print (1) copy
See more about our Environmental Commitment
Abstract
Preface This is the second edition of CSA Z259.2.4, Fall arresters and vertical rigid rails . It is part of a series of Standards on components of fall-protection systems and replaces the previous edition published in 2012. This Standard is considered suitable for use for conformity assessment within the stated scope of the Standard. CSA gratefully acknowledges the financial and in-kind support from the Canadian government departments responsible for occupational health and safety for the development of this edition. This Standard was prepared by the Subcommittee on Fall Arresters and Vertical Rigid Rails, under the jurisdiction of the Technical Committee on Fall Protection and the Strategic Steering Committee on Occupational Health and Safety, and has been formally approved by the Technical Committee. Scope 1.1 This Standard specifies design, testing, and marking requirements for manufactured fall arresters and fixed vertical rigid rails that are used on a vertical or sloped plane. 1.2 The equipment specified in this Standard is intended for use where there is a danger of falling from heights. In the event of fall, the fall arrester will lock on the fixed vertical rigid rail to arrest the fall. 1.3 This Standard does not cover work positioning and horizontal travel systems. 1.4 The values given in SI units are the units of record for the purposes of this Standard. The values given in parentheses are for information and comparison only. 1.5 In this Standard, "shall" is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; "should" is used to express a recommendation or that which is advised but not required; and "may" is used to express an option or that which is permissible within the limits of the Standard. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.
Previous Editions
Can’t find what you are looking for?
Please contact us at:
Related Documents
-

CSA Z434.1:26 – Use of industrial robot cells
CDN $1,416.00 Add to cart -

CSA Z5300:19 (R2024) – Cellulose filaments (CF) — Preparing handsheets for physical tests
CDN $197.00 Add to cart -

CSA Z94.3:26 – Eye and face protectors
CDN $197.00 Add to cart -

CSA Z462:21 – Workplace electrical safety
CDN $315.00 Add to cart







