
CSA C62155:06 (R2025)
CSA C62155:06 (R2025) – Hollow pressurized and unpressurized ceramic and glass insulators for use in electrical equipment with rated voltages greater than 1 000 V (Adopted CEI/IEC 62155:2003, first edition, 2003-05, with Canadian deviations) | Isolateurs creux avec ou sans pression interne, en matière céramique ou en verre, pour utilisation dans des appareillages prévus pour des tensions nominales supérieures à 1000 V (norme CEI/IEC 62155:2003 adoptée, première édition, 2003-05, avec exigences propres au Canada)
CDN $331.00
Hollow pressurized and unpressurized ceramic and glass insulators for use in electrical equipment with rated voltages greater than 1 000 V (Adopted CEI/IEC 62155:2003, first edition, 2003-05, with Canadian deviations) | Isolateurs creux avec ou sans pression interne, en matière céramique ou en verre, pour utilisation dans des appareillages prévus pour des tensions nominales supérieures à 1000 V (norme CEI/IEC 62155:2003 adoptée, première édition, 2003-05, avec exigences propres au Canada)
Description
CSA Preface This is the first edition of CAN/CSA-C62155, Hollow pressurized and unpressurized ceramic and glass insulators for use in electrical equipment with rated voltages greater than 1 000 V , which is an adoption, with Canadian deviations, of the identically titled CEI/IEC (Commission Électrotechnique Internationale/International Electrotechnical Commission) Standard 62155 (first edition, 2003-05). It replaces CAN/CSA-C1264-99, Ceramic pressurized hollow insulators for high-voltage switchgear and controlgear (adopted CEI/IEC 1264:1994). This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group. Scope and objec t 1.1 General This standard is applicable to – ceramic and glass hollow insulators intended for general use in electrical equipment; – ceramic hollow insulators intended for use with a permanent gas pressure in switchgear and controlgear. These insulators are intended for indoor and outdoor use in electrical equipment, operating on alternating current with a rated voltage greater than 1 000 V and a frequency not greater than 100 Hz or for use in direct-current equipment with a rated voltage of greater than 1 500 V. The hollow insulators are intended for use in electrical equipment, for example: – circuit-breakers – switch-disconnectors – disconnectors – earthing switches – instrument transformers – surge arresters – bushings – cable sealing ends – capacitors. It is not the object of this standard to prescribe dielectric type tests because the withstand voltages are not characteristics of the hollow insulator itself but of the apparatus of which it ultimately forms a part. 1.2 Hollow insulators or hollow insulator bodies intended for general use Hollow insulators or insulator bodies of ceramic material or glass, intended for use – without pressure – with permanent pressure .50 kPa gauge – with permanent gas pressure >50 kPa gauge in combination with an internal volume 50 kPa en combinaison avec un volume interieur < 1 l (1 000 cm3) – avec pression hydraulique permanente.
Edition
Not found
Published Date
2026-10-05
Status
Not found
Pages
115
Format 
Secure PDF
Secure – PDF details
- Save your file locally or view it via a web viewer
- Viewing permissions are restricted exclusively to the purchaser
- Device limits - 3
- Printing – Enabled only to print (1) copy
See more about our Environmental Commitment
Abstract
CSA Preface This is the first edition of CAN/CSA-C62155, Hollow pressurized and unpressurized ceramic and glass insulators for use in electrical equipment with rated voltages greater than 1 000 V , which is an adoption, with Canadian deviations, of the identically titled CEI/IEC (Commission Électrotechnique Internationale/International Electrotechnical Commission) Standard 62155 (first edition, 2003-05). It replaces CAN/CSA-C1264-99, Ceramic pressurized hollow insulators for high-voltage switchgear and controlgear (adopted CEI/IEC 1264:1994). This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group. Scope and objec t 1.1 General This standard is applicable to - ceramic and glass hollow insulators intended for general use in electrical equipment; - ceramic hollow insulators intended for use with a permanent gas pressure in switchgear and controlgear. These insulators are intended for indoor and outdoor use in electrical equipment, operating on alternating current with a rated voltage greater than 1 000 V and a frequency not greater than 100 Hz or for use in direct-current equipment with a rated voltage of greater than 1 500 V. The hollow insulators are intended for use in electrical equipment, for example: - circuit-breakers - switch-disconnectors - disconnectors - earthing switches - instrument transformers - surge arresters - bushings - cable sealing ends - capacitors. It is not the object of this standard to prescribe dielectric type tests because the withstand voltages are not characteristics of the hollow insulator itself but of the apparatus of which it ultimately forms a part. 1.2 Hollow insulators or hollow insulator bodies intended for general use Hollow insulators or insulator bodies of ceramic material or glass, intended for use - without pressure - with permanent pressure .50 kPa gauge - with permanent gas pressure >50 kPa gauge in combination with an internal volume 50 kPa en combinaison avec un volume interieur < 1 l (1 000 cm3) - avec pression hydraulique permanente.
Previous Editions
Can’t find what you are looking for?
Please contact us at:
Related Documents
-

CSA E61347-1:24 – Lamp controlgear – Part 1: General and safety requirements (Adopted IEC 61347-1:2015, edition 3:2015 consolidated with amendment 1:2017, with Canadian deviations) | Appareillages de lampes – Partie 1 : Exigences générales et exigences de sécurité (norme IEC 61347-1:2015 adoptée, édition 3:2015 consolidée par l’amendement 1:2017), avec exigences propres au Canada)
CDN $907.00 Add to cart -

IEEE 844.2-2017/CSA C293.2:17 (R2022) – Skin effect trace heating of pipelines, vessels, equipment, and structures—Application guide for design, installation, testing, commissioning, and maintenance
CDN $158.00 Add to cart -

IEEE 844.3-2019/CSA C22.2 NO. 293.3:19 (R2024) – Impedance heating of pipelines and equipment—General, testing, marking, and documentation requirements
CDN $174.00 Add to cart -

CSA E62660-2:21 (R2026) – Secondary lithium-ion cells for the propulsion of electric road vehicles – Part 2: Reliability and abuse testing (Adopted IEC 62660-2:2018, second edition, 2018-12, with Canadian deviations) | Éléments d’accumulateurs lithium-ion pour la propulsion des véhicules routiers électriques – Partie 2 : Essais de fiabilité et de traitement abusif (norme IEC 62660-2:2018 adoptée, deuxième édition, 2018-12, avec exigences propres au Canada)
CDN $225.00 Add to cart







