
CSA C22.2 NO. 745-4-36:95 (R2023)
CSA C22.2 NO. 745-4-36:95 (R2023) – Safety of portable battery-operated tools – Part 4: Particular requirements for hand motor tools (Binational standard with UL 745-4-36)
CDN $420.00
Safety of portable battery-operated tools – Part 4: Particular requirements for hand motor tools (Binational standard with UL 745-4-36)
Description
Preface This is the common GSA and UL Standard for portable battery-operated hand motor tools. It is the first edition of CSA Standard CAN/CSA-C22.2 No. 745-4-36, Safety of portable battery-operated tools — Part 4: Particular requirements for hand motor tools and UL 745-4-3 6, Safety of portable battery-operated tools — Part 4: Particular requirements for hand motor tools. It is written in SI (metric) units. It will coexist with the GSA Standard CAN/CSA-C22.2 No. 71.1 for the period given in CSA Certification Notice — Electrical Tools No. 6. This Standard was prepared by the Canadian Standards Association and Underwriters Laboratories Inc. This Standard contains particular requirements and is intended to be used in conjunction with the general Standard CAN/CSA-C22.2 No. 745-3/UL 745-3. Where a particular clause of the general Standard (CAN/CSA-C22.2 No. 745-3/UL 745-3) is not mentioned in this Standard, the clause applies as far as is reasonable. Where this particular Standard states addition, modification, or replacement, the relevant requirement, test specification, or explanatory matter in the general Standard (CAN/CSA-C22.2 No. 745-3/UL 745-3) should be adapted accordingly. If the functions of a tool are covered by different particular Standards, the relevant particular Standard is applied to each function separately, so far as is reasonable. If applicable, the influence of one function on the other is taken into account. This Standard was reviewed by the CSA Subcommittee on Portable Electric Tools of the Technical Committee on Consumer and Commercial Products under the jurisdiction of the Standards Steering Committee on the Canadian Electrical Code, Part II, and was formally approved by these Committees. This Standard was processed and reviewed in accordance with the method of development, revision, and implementation of UL Standards for safety. This Standard has been approved by the Standards Council of Canada as a National Standard of Canada and it will be submitted to the American National Standards Institute (ANSI) for publication as an American National Standard. Scope This clause of Part 3 is applicable, except as follows: 1.1 Replacement: The term “tools” is replaced by “hand motor tools.”
Edition
Not found
Published Date
2026-10-05
Status
Not found
Pages
23
Format 
Secure PDF
Secure – PDF details
- Save your file locally or view it via a web viewer
- Viewing permissions are restricted exclusively to the purchaser
- Device limits - 3
- Printing – Enabled only to print (1) copy
See more about our Environmental Commitment
Abstract
Preface This is the common GSA and UL Standard for portable battery-operated hand motor tools. It is the first edition of CSA Standard CAN/CSA-C22.2 No. 745-4-36, Safety of portable battery-operated tools — Part 4: Particular requirements for hand motor tools and UL 745-4-3 6, Safety of portable battery-operated tools — Part 4: Particular requirements for hand motor tools. It is written in SI (metric) units. It will coexist with the GSA Standard CAN/CSA-C22.2 No. 71.1 for the period given in CSA Certification Notice — Electrical Tools No. 6. This Standard was prepared by the Canadian Standards Association and Underwriters Laboratories Inc. This Standard contains particular requirements and is intended to be used in conjunction with the general Standard CAN/CSA-C22.2 No. 745-3/UL 745-3. Where a particular clause of the general Standard (CAN/CSA-C22.2 No. 745-3/UL 745-3) is not mentioned in this Standard, the clause applies as far as is reasonable. Where this particular Standard states addition, modification, or replacement, the relevant requirement, test specification, or explanatory matter in the general Standard (CAN/CSA-C22.2 No. 745-3/UL 745-3) should be adapted accordingly. If the functions of a tool are covered by different particular Standards, the relevant particular Standard is applied to each function separately, so far as is reasonable. If applicable, the influence of one function on the other is taken into account. This Standard was reviewed by the CSA Subcommittee on Portable Electric Tools of the Technical Committee on Consumer and Commercial Products under the jurisdiction of the Standards Steering Committee on the Canadian Electrical Code, Part II, and was formally approved by these Committees. This Standard was processed and reviewed in accordance with the method of development, revision, and implementation of UL Standards for safety. This Standard has been approved by the Standards Council of Canada as a National Standard of Canada and it will be submitted to the American National Standards Institute (ANSI) for publication as an American National Standard. Scope This clause of Part 3 is applicable, except as follows: 1.1 Replacement: The term "tools" is replaced by "hand motor tools."
Previous Editions
Can’t find what you are looking for?
Please contact us at:
Related Documents
-

IEEE 844.4-2019/CSA C293.4:19 (R2024) – Impedance heating of pipelines and equipment—Application guide for design, installation, testing, commissioning, and maintenance
CDN $174.00 Add to cart -

CSA G12:14 (R2024) – Zinc-coated steel wire strand
CDN $136.00 Add to cart -

CSA E61959:14 (R2024) – Secondary cells and batteries containing alkaline or other non-acid electrolytes – Mechanical tests for sealed portable secondary cells and batteries (Adopted IEC 61959:2004, first edition, 2004-01, with Canadian deviations) | Accumulateurs alcalins et autres accumulateurs à électrolyte non acide – Essais mécaniques pour accumulateurs portables étanches (norme CEI 61959:2004 adoptée, première édition, 2004-01, avec exigences propres au Canada)
CDN $56.00 Add to cart -

CSA E61558-2-5:25 – Safety of transformers, reactors, power supply units and combinations thereof — Part 2-5: Particular requirements and tests for transformers for shavers, power supply units for shavers and shaver supply units (Adopted IEC 61558-2-5:2024, third edition, 2024-08, with Canadian deviations) | Sécurité des transformateurs, bobines d’inductance, blocs d’alimentation et combinaisons de ces éléments — Partie 2-5 : Exigences particulières et essais pour les transformateurs pour rasoirs, les blocs d’alimentation incorporant un transformateur pour rasoir et les blocs d’alimentation pour rasoirs (norme IEC 61558-2-5:2024 adoptée, troisième édition, 2024-08, avec exigences propres au Canada)
CDN $299.00 Add to cart







