
CSA C22.2 NO. 346:22
CSA C22.2 NO. 346:22 – DC charging equipment for electric vehicles (Trinational standard with UL 2202 and NMX-J-817-ANCE-2022)
CDN $724.00
DC charging equipment for electric vehicles (Trinational standard with UL 2202 and NMX-J-817-ANCE-2022)
Description
Preface This is the harmonized ANCE, CSA Group, and UL standard for DC Charging Equipment for Electric Vehicles . It is the first edition of NMX-J-817-ANCE, the first edition of CSA C22.2 No. 346, and the third edition of UL 2202. This edition of UL 2202 supersedes the previous edition(s) published on October 2, 2009, titled Electric Vehicle (EV) Charging System Equipment. This harmonized standard was prepared by the Association of Standardization and Certification, (ANCE), CSA Group and Underwriters Laboratories Inc. (UL). The efforts and support of the Technical Harmonization Committee for Electric Vehicle Supply Equipment of the Harmonization of Electrotechnical Standards of the Nations of the Americas (CANENA) are gratefully acknowledged. This standard is considered suitable for use for conformity assessment within the stated scope of the standard. The present Mexican standard was developed by the GT CONANCE from the Comite de Normalizacion de la Asociacion de Normalizacion y Certificacion, A.C., CONANCE, with the collaboration of different type of manufacturers and users. This standard was reviewed by the CSA Subcommittee on DC Fast Charging System for Electric Vehicles, under the jurisdiction of the CSA Technical Committee on Industrial Products and the CSA Strategic Steering Committee on Requirements on Electrical Safety, and has been formally approved by the CSA Technical Committee. This standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group. Scope 1.1 These requirements apply to DC conductive charging equipment intended to be supplied with a maximum input voltage of 1000 V ac or 1500 V dc, for recharging the propulsion batteries in over-the-road electric vehicles (EV). DC charging equipment for EV installations are intended for either: a) Dry location only, or b) Dry, wet, and damp location. Equipment is intended to be installed in accordance with the Installation Codes in Annex A, Ref. No. 1. 1.2 The output of the DC charging equipment for EV shall not exceed 1500 V dc. 1.3 For the purposes of this Standard, the term “electric vehicle”, designated throughout by the initials “EV”, is considered to cover electric vehicles, hybrid electric vehicles, and plug-in versions of these vehicles. 1.4 DC charging equipment for EV that is not a complete assembly and depends upon installation in an end product for compliance with the requirements in this Standard is investigated under the requirements of this Standard and the standard for the end product. 1.5 These requirements do not cover battery chargers covered by Annex A, Ref. Nos. 2 and 3. 1.6 These requirements do not cover on-board chargers. 1.7 These requirements do not cover electric vehicle supply equipment covered by Annex A, Ref. No. 4. 1.8 These requirements do not cover DC charging equipment for EV intended to be used in hazardous locations, such as near fuel dispensing stations.
Edition
Not found
Published Date
2026-10-05
Status
Not found
Pages
137
Format 
Secure PDF
Secure – PDF details
- Save your file locally or view it via a web viewer
- Viewing permissions are restricted exclusively to the purchaser
- Device limits - 3
- Printing – Enabled only to print (1) copy
See more about our Environmental Commitment
Abstract
Preface This is the harmonized ANCE, CSA Group, and UL standard for DC Charging Equipment for Electric Vehicles . It is the first edition of NMX-J-817-ANCE, the first edition of CSA C22.2 No. 346, and the third edition of UL 2202. This edition of UL 2202 supersedes the previous edition(s) published on October 2, 2009, titled Electric Vehicle (EV) Charging System Equipment. This harmonized standard was prepared by the Association of Standardization and Certification, (ANCE), CSA Group and Underwriters Laboratories Inc. (UL). The efforts and support of the Technical Harmonization Committee for Electric Vehicle Supply Equipment of the Harmonization of Electrotechnical Standards of the Nations of the Americas (CANENA) are gratefully acknowledged. This standard is considered suitable for use for conformity assessment within the stated scope of the standard. The present Mexican standard was developed by the GT CONANCE from the Comite de Normalizacion de la Asociacion de Normalizacion y Certificacion, A.C., CONANCE, with the collaboration of different type of manufacturers and users. This standard was reviewed by the CSA Subcommittee on DC Fast Charging System for Electric Vehicles, under the jurisdiction of the CSA Technical Committee on Industrial Products and the CSA Strategic Steering Committee on Requirements on Electrical Safety, and has been formally approved by the CSA Technical Committee. This standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group. Scope 1.1 These requirements apply to DC conductive charging equipment intended to be supplied with a maximum input voltage of 1000 V ac or 1500 V dc, for recharging the propulsion batteries in over-the-road electric vehicles (EV). DC charging equipment for EV installations are intended for either: a) Dry location only, or b) Dry, wet, and damp location. Equipment is intended to be installed in accordance with the Installation Codes in Annex A, Ref. No. 1. 1.2 The output of the DC charging equipment for EV shall not exceed 1500 V dc. 1.3 For the purposes of this Standard, the term "electric vehicle", designated throughout by the initials "EV", is considered to cover electric vehicles, hybrid electric vehicles, and plug-in versions of these vehicles. 1.4 DC charging equipment for EV that is not a complete assembly and depends upon installation in an end product for compliance with the requirements in this Standard is investigated under the requirements of this Standard and the standard for the end product. 1.5 These requirements do not cover battery chargers covered by Annex A, Ref. Nos. 2 and 3. 1.6 These requirements do not cover on-board chargers. 1.7 These requirements do not cover electric vehicle supply equipment covered by Annex A, Ref. No. 4. 1.8 These requirements do not cover DC charging equipment for EV intended to be used in hazardous locations, such as near fuel dispensing stations.
Previous Editions
Can’t find what you are looking for?
Please contact us at:
Related Documents
-

CSA E61558-2-13:25 – Safety of transformers, reactors, power supply units and combinations thereof — Part 2-13: Particular requirements and tests for auto-transformers and power supply units incorporating auto-transformers for general applications (Adopted IEC 61558-2-13:2022, third edition, 2022-10, with Canadian deviations) | Sécurité des transformateurs, bobines d’inductance, blocs d’alimentation et combinaisons de ces éléments — Partie 2-13 : Exigences particulières et essais pour les autotransformateurs et les blocs d’alimentation qui incorporent des autotransformateurs pour applications d’ordre général (norme IEC 61558-2-13:2022 adoptée, troisième édition, 2022-10, avec exigences propres au Canada)
CDN $205.00 Add to cart -

IEEE 844.1-2017/CSA C22.2 NO. 293.1:17 (R2022) – Skin effect trace heating of pipelines, vessels, equipment, and structures—General, testing, marking, and documentation requirements
CDN $158.00 Add to cart -

IEEE 844.2-2017/CSA C293.2:17 (R2022) – Skin effect trace heating of pipelines, vessels, equipment, and structures—Application guide for design, installation, testing, commissioning, and maintenance
CDN $158.00 Add to cart -

IEEE 844.4-2019/CSA C293.4:19 (R2024) – Impedance heating of pipelines and equipment—Application guide for design, installation, testing, commissioning, and maintenance
CDN $174.00 Add to cart







