
CSA C22.2 NO. 165:17 (R2022)
CSA C22.2 NO. 165:17 (R2022) – Electric boilers
CDN $197.00
Electric boilers
Description
Preface This is the second edition of CSA C22.2 No. 165, Electric boilers , one of a series of Standards issued by CSA Group under Part II of the Canadian Electrical Code. This edition supersedes the first edition published in 1992. This Standard applies to stationary hot-water and steam boilers for residential, commercial, and industrial use that utilize metal-sheathed immersion-type heater elements and are intended for permanent connection to the source of supply. It does not apply to electrode-type boilers. The changes to this edition are as follows: a) reference documents updated; b) requirements modified for plated and unplated parts; c) references to transformer standards updated; d) references to IEC-based standards added; and e) Table 8 updated and reformatted. This Standard sets minimum requirements that are not intended to conflict with or supersede the requirements of CSA B51 or other applicable standards for boilers that fall under the provisions of the Boilers and Pressure Vessels Act of the provinces or territories of Canada. For general information on the standards of the Committee on Canadian Electrical Code, Part II, see the Preface of CAN/CSA-C22.2, No. 0, General Requirements — Canadian Electrical Code, Part II. This Standard is considered suitable for conformity assessment within the stated scope of the Standard. This Standard was prepared by the Subcommittee on Electric Boilers, under the jurisdiction of the Technical Committee on Industrial Products and the Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the Technical Committee. This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group. Scope 1.1 This Standard applies to stationary, permanently connected, hot-water and steam boilers for use with nominal system voltages of 600 V and less, for residential, commercial, and industrial use in nonhazardous locations in accordance with the Rules of the Canadian Electrical Code, Part I. 1.2 This Standard applies to boilers utilizing metal-sheathed-type heater elements. 1.3 This Standard does not apply to a) storage-type water heaters as covered in CAN/CSA-C22.2 No. 110; b) swimming pool and spa hot-water heaters; c) electrode-type boilers; d) industrial heating equipment covered in CSA C22.2 No. 88; or e) electric heating equipment for medical and dental use. 1.4 This Standard sets minimum requirements. It is not intended that the requirements of this Standard conflict with or supersede the requirements of CSA B51 or any other applicable standard for boilers that fall under the provisions of the Boilers and Pressure Vessels Act of the provinces or territories of Canada. 1.5 In this Standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the Standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the Standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.
Edition
Not found
Published Date
2026-10-05
Status
Not found
Pages
53
Format 
Secure PDF
Secure – PDF details
- Save your file locally or view it via a web viewer
- Viewing permissions are restricted exclusively to the purchaser
- Device limits - 3
- Printing – Enabled only to print (1) copy
See more about our Environmental Commitment
Abstract
Preface This is the second edition of CSA C22.2 No. 165, Electric boilers , one of a series of Standards issued by CSA Group under Part II of the Canadian Electrical Code. This edition supersedes the first edition published in 1992. This Standard applies to stationary hot-water and steam boilers for residential, commercial, and industrial use that utilize metal-sheathed immersion-type heater elements and are intended for permanent connection to the source of supply. It does not apply to electrode-type boilers. The changes to this edition are as follows: a) reference documents updated; b) requirements modified for plated and unplated parts; c) references to transformer standards updated; d) references to IEC-based standards added; and e) Table 8 updated and reformatted. This Standard sets minimum requirements that are not intended to conflict with or supersede the requirements of CSA B51 or other applicable standards for boilers that fall under the provisions of the Boilers and Pressure Vessels Act of the provinces or territories of Canada. For general information on the standards of the Committee on Canadian Electrical Code, Part II, see the Preface of CAN/CSA-C22.2, No. 0, General Requirements — Canadian Electrical Code, Part II. This Standard is considered suitable for conformity assessment within the stated scope of the Standard. This Standard was prepared by the Subcommittee on Electric Boilers, under the jurisdiction of the Technical Committee on Industrial Products and the Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the Technical Committee. This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group. Scope 1.1 This Standard applies to stationary, permanently connected, hot-water and steam boilers for use with nominal system voltages of 600 V and less, for residential, commercial, and industrial use in nonhazardous locations in accordance with the Rules of the Canadian Electrical Code, Part I. 1.2 This Standard applies to boilers utilizing metal-sheathed-type heater elements. 1.3 This Standard does not apply to a) storage-type water heaters as covered in CAN/CSA-C22.2 No. 110; b) swimming pool and spa hot-water heaters; c) electrode-type boilers; d) industrial heating equipment covered in CSA C22.2 No. 88; or e) electric heating equipment for medical and dental use. 1.4 This Standard sets minimum requirements. It is not intended that the requirements of this Standard conflict with or supersede the requirements of CSA B51 or any other applicable standard for boilers that fall under the provisions of the Boilers and Pressure Vessels Act of the provinces or territories of Canada. 1.5 In this Standard, "shall" is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the Standard; "should" is used to express a recommendation or that which is advised but not required; and "may" is used to express an option or that which is permissible within the limits of the Standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.
Previous Editions
Can’t find what you are looking for?
Please contact us at:
Related Documents
-

CSA E61959:14 (R2024) – Secondary cells and batteries containing alkaline or other non-acid electrolytes – Mechanical tests for sealed portable secondary cells and batteries (Adopted IEC 61959:2004, first edition, 2004-01, with Canadian deviations) | Accumulateurs alcalins et autres accumulateurs à électrolyte non acide – Essais mécaniques pour accumulateurs portables étanches (norme CEI 61959:2004 adoptée, première édition, 2004-01, avec exigences propres au Canada)
CDN $56.00 Add to cart -

CSA E62660-2:21 (R2026) – Secondary lithium-ion cells for the propulsion of electric road vehicles – Part 2: Reliability and abuse testing (Adopted IEC 62660-2:2018, second edition, 2018-12, with Canadian deviations) | Éléments d’accumulateurs lithium-ion pour la propulsion des véhicules routiers électriques – Partie 2 : Essais de fiabilité et de traitement abusif (norme IEC 62660-2:2018 adoptée, deuxième édition, 2018-12, avec exigences propres au Canada)
CDN $225.00 Add to cart -

CAN/CSA-E61965:04 (R2023) – Mechanical safety of cathode ray tubes (Adopted IEC 61965:2003, second edition, 2003-07, with Canadian deviations)
CDN $356.00 Add to cart -

CSA SPE-3000:19 – Model code for the field evaluation of medical electrical equipment (MEE) and medical electrical systems (MES)
CDN $334.00 Add to cart







