
CSA C22.2 NO. 145:22
CSA C22.2 NO. 145:22 – Electric motors and generators for use in hazardous (classified) locations (Trinational standard with NMX-J-652-ANCE and UL 674)
CDN $850.00
Electric motors and generators for use in hazardous (classified) locations (Trinational standard with NMX-J-652-ANCE and UL 674)
Description
Preface This is the harmonized ANCE, CSA Group, and UL standard for Electric Motors and Generators for Use in Hazardous (Classified) Locations. It is the second edition of NMX-J-652-ANCE, the fourth edition of CSA C22.2 No. 145, and the sixth edition of UL 674. This edition of CSA C22.2 No. 145 supersedes the previous editions published in 1972, 1986 and 2011. This edition of UL 674 supersedes the previous edition published in 2011. This harmonized standard was prepared by the Association of Standardization and Certification (ANCE), the Canadian Standards Association (CSA), and Underwriters Laboratories Inc. (UL). The efforts and support of the CANENA Technical Harmonization Committee are gratefully acknowledged. This standard is considered suitable for use for conformity assessment within the stated scope of the standard. This standard was reviewed by the CSA Integrated Committee on Hazardous Location Products, under the jurisdiction of the CSA Technical Committee on Industrial Products and the CSA Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the CSA Technical Committee. Scope 1.1 This standard applies to electric motors and generators or submersible and nonsubmersible sewage pumps and systems suitable for use in Class I, Division 1, Groups B, C and D, and Class II, Division 1, Groups E, F and G, hazardous (classified) locations as defined by CSA C22.1 Canadian Electrical Code, Part I (CE Code), the National Electrical Code, ANSI/NFPA 70 (NEC), and NOM-001-SEDE. Note: In the US, the application “hazardous locations” is referred to as “hazardous (classified) locations”. 1.2 This standard covers the same type of electrical equipment indicated in 1.1 for installation and use in Class I, Zone 1, Groups IIA and IIB, IIB+H2, and Zone 20 and 21 hazardous locations. 1.3 This standard also covers other rotating machinery such as, but not limited to, electric brakes, tachometers, encoders, and slip rings. 1.4 This standard does not address types of protection other than explosion-proof or dust-ignition-proof. 1.5 For Canada Only – This standard does not include Canadian energy efficiency or product performance requirements. For such requirements, see Annex A, item 19. It is possible that item 19 is referenced in whole or in part in federal, provincial, territorial, or local laws or regulations relating to energy efficiency or product performance. The appropriate governmental authorities should be consulted to confirm whether item 19 has been referenced in laws or regulations. Note: This standard also does not include U.S. energy efficiency requirements for electric motors used in hazardous (classified) locations.
Edition
Not found
Published Date
2026-10-05
Status
Not found
Pages
106
Format 
Secure PDF
Secure – PDF details
- Save your file locally or view it via a web viewer
- Viewing permissions are restricted exclusively to the purchaser
- Device limits - 3
- Printing – Enabled only to print (1) copy
See more about our Environmental Commitment
Abstract
Preface This is the harmonized ANCE, CSA Group, and UL standard for Electric Motors and Generators for Use in Hazardous (Classified) Locations. It is the second edition of NMX-J-652-ANCE, the fourth edition of CSA C22.2 No. 145, and the sixth edition of UL 674. This edition of CSA C22.2 No. 145 supersedes the previous editions published in 1972, 1986 and 2011. This edition of UL 674 supersedes the previous edition published in 2011. This harmonized standard was prepared by the Association of Standardization and Certification (ANCE), the Canadian Standards Association (CSA), and Underwriters Laboratories Inc. (UL). The efforts and support of the CANENA Technical Harmonization Committee are gratefully acknowledged. This standard is considered suitable for use for conformity assessment within the stated scope of the standard. This standard was reviewed by the CSA Integrated Committee on Hazardous Location Products, under the jurisdiction of the CSA Technical Committee on Industrial Products and the CSA Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the CSA Technical Committee. Scope 1.1 This standard applies to electric motors and generators or submersible and nonsubmersible sewage pumps and systems suitable for use in Class I, Division 1, Groups B, C and D, and Class II, Division 1, Groups E, F and G, hazardous (classified) locations as defined by CSA C22.1 Canadian Electrical Code, Part I (CE Code), the National Electrical Code, ANSI/NFPA 70 (NEC), and NOM-001-SEDE. Note: In the US, the application "hazardous locations" is referred to as "hazardous (classified) locations". 1.2 This standard covers the same type of electrical equipment indicated in 1.1 for installation and use in Class I, Zone 1, Groups IIA and IIB, IIB+H2, and Zone 20 and 21 hazardous locations. 1.3 This standard also covers other rotating machinery such as, but not limited to, electric brakes, tachometers, encoders, and slip rings. 1.4 This standard does not address types of protection other than explosion-proof or dust-ignition-proof. 1.5 For Canada Only – This standard does not include Canadian energy efficiency or product performance requirements. For such requirements, see Annex A, item 19. It is possible that item 19 is referenced in whole or in part in federal, provincial, territorial, or local laws or regulations relating to energy efficiency or product performance. The appropriate governmental authorities should be consulted to confirm whether item 19 has been referenced in laws or regulations. Note: This standard also does not include U.S. energy efficiency requirements for electric motors used in hazardous (classified) locations.
Previous Editions
Can’t find what you are looking for?
Please contact us at:
Related Documents
-

CSA E61347-1:24 – Lamp controlgear – Part 1: General and safety requirements (Adopted IEC 61347-1:2015, edition 3:2015 consolidated with amendment 1:2017, with Canadian deviations) | Appareillages de lampes – Partie 1 : Exigences générales et exigences de sécurité (norme IEC 61347-1:2015 adoptée, édition 3:2015 consolidée par l’amendement 1:2017), avec exigences propres au Canada)
CDN $907.00 Add to cart -

CSA SPE-1000:25 – Model Code for the field evaluation of electrical equipment
CDN $378.00 Add to cart -

CAN/CSA-E61558-1:12 (R2022) – Safety of power transformers, power supplies, reactors and similar products – Part 1: General requirements and tests (Adopted IEC 61558- 1:1997 + A1:1998, edition 2.1, 2009-04 with Canadian deviations) | Sécurité des transformateurs, alimentations, bobines d’inductance et produits analogues – Partie 1: Exigences générales et essais (norme CEI 61558-1:1997 + A1:1998 adoptée, édition 2.1, 2009-04 avec exigences propres au Canada)
CDN $630.00 Add to cart -

CSA G12:14 (R2024) – Zinc-coated steel wire strand
CDN $136.00 Add to cart







