
CSA C22.2 NO. 127:24
CSA C22.2 NO. 127:24 – Equipment wires, lead wires, and decorative cords
CDN $504.00
Equipment wires, lead wires, and decorative cords
Description
Preface This is the tenth edition of CSA C22.2 No. 127, Equipment wires, lead wires, and decorative cords . It supersedes the previous editions, published in 2018, 2015, 2009, 1999, 1995, 1988, 1981, 1966, and 1964 under the title Equipment and lead wires. It is one of a series of Standards issued by CSA Group under Part II of the Canadian Electrical Code. The major changes to this edition include the following: a) removing cords for decorative lighting from the scope of CSA C22.2 No. 49 and incorporating them into the scope of this Standard; b) adding a mandatory FT2 flame test to all decorative cord types; c) adding requirements for marking and tests for laser printing; d) updating Table 34 from “Mandrel diameter for ‘U’ bend discharge test” to “Mandrel diameter for cold bend test”; and e) updating test method references to CSA C22.2 No. 2556. This Standard is considered suitable for use for conformity assessment within the stated scope of the Standard. This Standard was prepared by the Integrated Committee on Flexible Cords/Equipment and Appliance Wires and Cables, under the jurisdiction of the Technical Committee on Wiring Products and the Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the Technical Committee. This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group. Scope 1.1 This Standard applies to the following products to be installed in accordance with the Canadian Electrical Code, Part I: a) cords and insulated conductors intended for decorative lighting and seasonal-use cord sets; and b) insulated conductors intended for internal wiring of electrical equipment, for leads of transformers, motors, etc., and for luminous-tube signs and ignition systems. 1.2 Constructions to which this Standard applies are shown in Tables 1 and 2. The tables are not a complete summary of the construction details, but all of the items shown therein are requirements or limitations. 1.3 The values given in SI units are the units of record for the purposes of this Standard. The values given in parentheses are for information and comparison only. 1.4 In this Standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the Standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the Standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.
Edition
Not found
Published Date
2026-10-05
Status
Not found
Pages
139
Format 
Secure PDF
Secure – PDF details
- Save your file locally or view it via a web viewer
- Viewing permissions are restricted exclusively to the purchaser
- Device limits - 3
- Printing – Enabled only to print (1) copy
See more about our Environmental Commitment
Abstract
Preface This is the tenth edition of CSA C22.2 No. 127, Equipment wires, lead wires, and decorative cords . It supersedes the previous editions, published in 2018, 2015, 2009, 1999, 1995, 1988, 1981, 1966, and 1964 under the title Equipment and lead wires. It is one of a series of Standards issued by CSA Group under Part II of the Canadian Electrical Code. The major changes to this edition include the following: a) removing cords for decorative lighting from the scope of CSA C22.2 No. 49 and incorporating them into the scope of this Standard; b) adding a mandatory FT2 flame test to all decorative cord types; c) adding requirements for marking and tests for laser printing; d) updating Table 34 from "Mandrel diameter for ‘U’ bend discharge test" to "Mandrel diameter for cold bend test"; and e) updating test method references to CSA C22.2 No. 2556. This Standard is considered suitable for use for conformity assessment within the stated scope of the Standard. This Standard was prepared by the Integrated Committee on Flexible Cords/Equipment and Appliance Wires and Cables, under the jurisdiction of the Technical Committee on Wiring Products and the Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the Technical Committee. This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group. Scope 1.1 This Standard applies to the following products to be installed in accordance with the Canadian Electrical Code, Part I: a) cords and insulated conductors intended for decorative lighting and seasonal-use cord sets; and b) insulated conductors intended for internal wiring of electrical equipment, for leads of transformers, motors, etc., and for luminous-tube signs and ignition systems. 1.2 Constructions to which this Standard applies are shown in Tables 1 and 2. The tables are not a complete summary of the construction details, but all of the items shown therein are requirements or limitations. 1.3 The values given in SI units are the units of record for the purposes of this Standard. The values given in parentheses are for information and comparison only. 1.4 In this Standard, "shall" is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the Standard; "should" is used to express a recommendation or that which is advised but not required; and "may" is used to express an option or that which is permissible within the limits of the Standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.
Previous Editions
Can’t find what you are looking for?
Please contact us at:
Related Documents
-

CSA G164:26 – Galvanizing of irregularly shaped articles
CDN $142.00 Add to cart -

CAN/CSA-E61558-1:12 (R2022) – Safety of power transformers, power supplies, reactors and similar products – Part 1: General requirements and tests (Adopted IEC 61558- 1:1997 + A1:1998, edition 2.1, 2009-04 with Canadian deviations) | Sécurité des transformateurs, alimentations, bobines d’inductance et produits analogues – Partie 1: Exigences générales et essais (norme CEI 61558-1:1997 + A1:1998 adoptée, édition 2.1, 2009-04 avec exigences propres au Canada)
CDN $630.00 Add to cart -

CSA E61347-2-3:23 – Lamp control gear — Part 2-3: Particular requirements for a.c. and/or d.c. supplied electronic control gear for fluorescent lamps (Adopted IEC 61347-2-3:2011, edition 2:2011 consolidated with amendment 1:2016, with Canadian deviations) | Appareillages de lampes — Partie 2-3 : Exigences particulières pour les appareillages électroniques alimentés en courant alternatif et/ou en courant continu pour lampes fluorescentes (norme IEC 61347-2-3:2011 adoptée, édition 2:2011 consolidée par l’amendement 1:2016, avec exigences propres au Canada)
CDN $620.00 Add to cart -

CSA E61951-1:21 (R2026) – Secondary cells and batteries containing alkaline or other non-acid electrolytes — Secondary sealed cells and batteries for portable applications — Part 1: Nickel-cadmium (Adopted IEC 61951:2017, fourth edition, 2017-03, with Canadian deviations) | Accumulateurs alcalins et autres accumulateurs à électrolyte non acide — Accumulateurs étanches pour applications portables — Partie 1 : Nickel-cadmium (norme IEC 61951-1:2017 adoptée, quatrième édition, 2017-03), avec exigences propres au Canada)
CDN $527.00 Add to cart







