Sky Bear Technical Standards - Home
Search
×
FR

Placeholder headline

This is just a placeholder headline

B51-14 (R2019) – Boiler, pressure vessel, and pressure piping code

$

362

BUY NOW

ANSI Z21.93-2017 (R2022)/CSA 6.30-2017 (R2022)

ANSI Z21.93-2017 (R2022)/CSA 6.30-2017 (R2022) – Excess flow valves for natural gas and propane gas with pressures up to 5 psig

CDN $584.00

Excess flow valves for natural gas and propane gas with pressures up to 5 psig

SKU: 2424174 Categories: ,

Description

Preface This is the second edition of ANSI Z21.93 • CSA 6.30, Excess flow valves for natural gas and propane gas with pressures up to 5 psig. It supersedes the previous edition published in 2013. This Standard was prepared by the Z21/CSA Joint Technical Subcommittee on Standards for Manual Valves, under the jurisdiction of the CSA and Z21/83 Technical Committees on the Performance and Installation of Gas Burning Appliances and Related Accessories and the Strategic Steering Committee on Standards for Gas Appliances and Related Accessories, and formally approved by the Technical Committee(s), American National Standards Institute, and the Interprovincial Gas Advisory Council. Scope 1.1 This Standard applies to excess flow valves constructed entirely of new unused parts and materials intended for use after the service meter or second stage regulator (see Clause 3, Definitions), hereinafter referred to as valves, not to exceed 2 in (50 DN) nominal pipe size. 1.2 Valves covered by this Standard automatically limits the downstream flow of gas in the event that the flow reaches the valve’s trip flow. 1.3 This Standard applies to valves for use with natural, manufactured and mixed gases, propane gas, and LP gas-air mixtures at pressures not to exceed 5 psi (35 kPa). 1.4 Valves are to have a minimum operating pressure of no greater than 5 in wc (1.24 kPa). 1.5 Valves are to be capable of operation within an ambient temperature range of -20°F to 150°F (-29 °C to 66 °C). Valves also are to be capable of operation at temperatures outside this specified range when so specified by the manufacturer. 1.6 If a value for measurement as given in this Standard is followed by an equivalent value in other units, the first stated value is to be regarded as the specification. 1.7 All references to pressure throughout this Standard are to be considered gauge pressures, unless otherwise specified. 1.8 This Standard contains SI (Metric) corresponding to the yard/pound quantities, the purpose being to allow the standard to be used in SI (Metric) units. (Standard for use of the International System of Units (SI): The Modern Metric System, IEEE/ASTM SI 10 or ISO 80000-1:2009 Quantities and units– Part 1: General are used as a guide in making metric conversion from yard/pound quantities.) If a value for a measurement and a corresponding value in other units are stated, the first stated value is to be regarded as the requirement. The given corresponding value may be approximate. If a value for a measurement and a corresponding value in other units are both specified as a quoted marking requirement, the first stated unit, or both shall be provided.

Edition

Not found

Published Date

2026-10-05

Status

Not found

Pages

59

Language Detail Icon

English

Format Secure Icon

Secure PDF

Abstract

Preface This is the second edition of ANSI Z21.93 • CSA 6.30, Excess flow valves for natural gas and propane gas with pressures up to 5 psig. It supersedes the previous edition published in 2013. This Standard was prepared by the Z21/CSA Joint Technical Subcommittee on Standards for Manual Valves, under the jurisdiction of the CSA and Z21/83 Technical Committees on the Performance and Installation of Gas Burning Appliances and Related Accessories and the Strategic Steering Committee on Standards for Gas Appliances and Related Accessories, and formally approved by the Technical Committee(s), American National Standards Institute, and the Interprovincial Gas Advisory Council. Scope 1.1 This Standard applies to excess flow valves constructed entirely of new unused parts and materials intended for use after the service meter or second stage regulator (see Clause 3, Definitions), hereinafter referred to as valves, not to exceed 2 in (50 DN) nominal pipe size. 1.2 Valves covered by this Standard automatically limits the downstream flow of gas in the event that the flow reaches the valve's trip flow. 1.3 This Standard applies to valves for use with natural, manufactured and mixed gases, propane gas, and LP gas-air mixtures at pressures not to exceed 5 psi (35 kPa). 1.4 Valves are to have a minimum operating pressure of no greater than 5 in wc (1.24 kPa). 1.5 Valves are to be capable of operation within an ambient temperature range of -20°F to 150°F (-29 °C to 66 °C). Valves also are to be capable of operation at temperatures outside this specified range when so specified by the manufacturer. 1.6 If a value for measurement as given in this Standard is followed by an equivalent value in other units, the first stated value is to be regarded as the specification. 1.7 All references to pressure throughout this Standard are to be considered gauge pressures, unless otherwise specified. 1.8 This Standard contains SI (Metric) corresponding to the yard/pound quantities, the purpose being to allow the standard to be used in SI (Metric) units. (Standard for use of the International System of Units (SI): The Modern Metric System, IEEE/ASTM SI 10 or ISO 80000-1:2009 Quantities and units– Part 1: General are used as a guide in making metric conversion from yard/pound quantities.) If a value for a measurement and a corresponding value in other units are stated, the first stated value is to be regarded as the requirement. The given corresponding value may be approximate. If a value for a measurement and a corresponding value in other units are both specified as a quoted marking requirement, the first stated unit, or both shall be provided.

Previous Editions

Can’t find what you are looking for?

Please contact us at: