
CSA C22.2 NO. 62841-3-3:25
CSA C22.2 NO. 62841-3-3:25 – Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery — Safety — Part 3-3: Particular requirements for transportable planers and thicknessers (Binational standard with UL 62841-3-3)
CDN $598.00
Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery — Safety — Part 3-3: Particular requirements for transportable planers and thicknessers (Binational standard with UL 62841-3-3)
Description
Preface This is the harmonized CSA Group and ULSE standard for Electric Motor-Operated Hand-Held Tools, Transportable Tools and Lawn and Garden Machinery – Safety – Part 3-3: Particular Requirements for Transportable Planers and Thicknessers . It is the First edition of CSA C22.2 No. 62841-3-3 and the First edition of UL 62841-3-3. This harmonized standard is based on IEC Publication 62841-3-3: First edition, Electric Motor-Operated Hand-Held Tools, Transportable Tools and Lawn and Garden Machinery – Safety – Part 3-3: Particular Requirements for Transportable Planers and Thicknessers, issued June 2024. IEC 62841-3-3 is copyrighted by the IEC. This harmonized standard was prepared by CSA Group and ULSE. The efforts and support of the International Harmonization Committee (IHC) for the adoption of the IEC series of standards for Hand-Held, Motor-Operated, and Transportable Tools and Lawn and Garden Machinery, are gratefully acknowledged. This Standard is considered suitable for use for conformity assessment within the stated scope of the standard. This Standard was reviewed by the CSA Subcommittee on Safety of Hand-Held Motor-Operated Electric Tools, under the jurisdiction of the CSA Technical Committee on Consumer and Commercial Products and the CSA Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the CSA Technical Committee. This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group. Scope IEC 62841-1:2014, Clause 1 is applicable, except as follows: Addition: This document applies to transportable planers, thicknessers and combined planers and thicknessers intended for cutting wood and analogous materials with a maximum planning width of 330 mm. This document does not apply to planers, thicknessers or combined planers and thicknessers other than transportable. NOTE 101 ISO 19085-7:2019 gives requirements for planers, thicknessers or combined planers and thicknessers other than transportable.
Edition
Not found
Published Date
2026-10-06
Status
Not found
Pages
56
Format 
Secure PDF
Secure – PDF details
- Save your file locally or view it via a web viewer
- Viewing permissions are restricted exclusively to the purchaser
- Device limits - 3
- Printing – Enabled only to print (1) copy
See more about our Environmental Commitment
Abstract
Preface This is the harmonized CSA Group and ULSE standard for Electric Motor-Operated Hand-Held Tools, Transportable Tools and Lawn and Garden Machinery – Safety – Part 3-3: Particular Requirements for Transportable Planers and Thicknessers . It is the First edition of CSA C22.2 No. 62841-3-3 and the First edition of UL 62841-3-3. This harmonized standard is based on IEC Publication 62841-3-3: First edition, Electric Motor-Operated Hand-Held Tools, Transportable Tools and Lawn and Garden Machinery – Safety – Part 3-3: Particular Requirements for Transportable Planers and Thicknessers, issued June 2024. IEC 62841-3-3 is copyrighted by the IEC. This harmonized standard was prepared by CSA Group and ULSE. The efforts and support of the International Harmonization Committee (IHC) for the adoption of the IEC series of standards for Hand-Held, Motor-Operated, and Transportable Tools and Lawn and Garden Machinery, are gratefully acknowledged. This Standard is considered suitable for use for conformity assessment within the stated scope of the standard. This Standard was reviewed by the CSA Subcommittee on Safety of Hand-Held Motor-Operated Electric Tools, under the jurisdiction of the CSA Technical Committee on Consumer and Commercial Products and the CSA Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the CSA Technical Committee. This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group. Scope IEC 62841-1:2014, Clause 1 is applicable, except as follows: Addition: This document applies to transportable planers, thicknessers and combined planers and thicknessers intended for cutting wood and analogous materials with a maximum planning width of 330 mm. This document does not apply to planers, thicknessers or combined planers and thicknessers other than transportable. NOTE 101 ISO 19085-7:2019 gives requirements for planers, thicknessers or combined planers and thicknessers other than transportable.
Previous Editions
Can’t find what you are looking for?
Please contact us at:
Related Documents
-

CSA G12:14 (R2024) – Zinc-coated steel wire strand
CDN $136.00 Add to cart -

IEEE 844.4-2019/CSA C293.4:19 (R2024) – Impedance heating of pipelines and equipment—Application guide for design, installation, testing, commissioning, and maintenance
CDN $174.00 Add to cart -

CSA G164:26 – Galvanizing of irregularly shaped articles
CDN $142.00 Add to cart -

CSA E61558-2-13:25 – Safety of transformers, reactors, power supply units and combinations thereof — Part 2-13: Particular requirements and tests for auto-transformers and power supply units incorporating auto-transformers for general applications (Adopted IEC 61558-2-13:2022, third edition, 2022-10, with Canadian deviations) | Sécurité des transformateurs, bobines d’inductance, blocs d’alimentation et combinaisons de ces éléments — Partie 2-13 : Exigences particulières et essais pour les autotransformateurs et les blocs d’alimentation qui incorporent des autotransformateurs pour applications d’ordre général (norme IEC 61558-2-13:2022 adoptée, troisième édition, 2022-10, avec exigences propres au Canada)
CDN $205.00 Add to cart







