
C22.2 NO. 21-18 (R2023)
C22.2 NO. 21-18 (R2023) – Cord sets and power-supply cords
CDN $1,338.00
Cord sets and power-supply cords
Description
Preface This is the tenth edition of CSA C22.2 No. 21, Cord sets and power supply cords. This edition supersedes previous editions published in 2014, 1995, 1990, 1984, 1978, 1960, 1954, 1941, and 1935 and is written in SI (metric) units, except the wire gauge sizes. This Standard is considered suitable for use for conformity assessment within the stated scope of the Standard. This Standard was prepared by the Integrated Committee on Wiring Devices, under the jurisdiction of the Technical Committee on Wiring Products and the Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the Technical Committee. This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group. Scope 1.1 This Standard specifies the requirements for cord sets and power-supply cords employing molded-on or assembled-on fittings, rated 600 V maximum, and intended for use in non-hazardous locations in accordance with CSA C22.1, Canadian Electrical Code, Part I, and CAN/CSA-C22.2 No. 0, General Requirements—Canadian Electrical Code, Part II. 1.2 This Standard also specifies the requirements for molded-on general-use attachment plugs and cord connectors. 1.3 This Standard also specifies the requirements for molded-on hospital grade attachment plugs and cord connectors. 1.4 This Standard also specifies the requirements for cord restraint devices. 1.5 These requirements do not cover cord sets intended for temporary outdoor use — not to exceed 90 days — with outdoor equipment, Christmas-tree, and other seasonal decorative-lighting outfits. 1.6 This Standard does not cover electric vehicle cord sets. Requirements for electric vehicle cord sets are listed in CSA C22.2 No. 282. 1.7 This Standard does not cover cord reels and power bars. Requirements for cord reels and power bars are listed in CSA C22.2 No. 308. 1.8 This Standard contains the following annexes: a) Annex A — Component standards reference list; b) Annex B — Illustrative definitions; c) Annex C — Canadian marking translations; d) Annex D — Marine shore power sets; e) Annex E — Manufacturing and production tests; and f) Annex F — Marine shore power cable sets. 1.9 In this Standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application. 1.10 The values given in SI units are the units of record for the purposes of this Standard. The values given in parentheses are for information and comparison only.
Edition
Not found
Published Date
2026-10-05
Status
Not found
Pages
184
Format 
Secure PDF
Secure – PDF details
- Save your file locally or view it via a web viewer
- Viewing permissions are restricted exclusively to the purchaser
- Device limits - 3
- Printing – Enabled only to print (1) copy
See more about our Environmental Commitment
Abstract
Preface This is the tenth edition of CSA C22.2 No. 21, Cord sets and power supply cords. This edition supersedes previous editions published in 2014, 1995, 1990, 1984, 1978, 1960, 1954, 1941, and 1935 and is written in SI (metric) units, except the wire gauge sizes. This Standard is considered suitable for use for conformity assessment within the stated scope of the Standard. This Standard was prepared by the Integrated Committee on Wiring Devices, under the jurisdiction of the Technical Committee on Wiring Products and the Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the Technical Committee. This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group. Scope 1.1 This Standard specifies the requirements for cord sets and power-supply cords employing molded-on or assembled-on fittings, rated 600 V maximum, and intended for use in non-hazardous locations in accordance with CSA C22.1, Canadian Electrical Code, Part I, and CAN/CSA-C22.2 No. 0, General Requirements—Canadian Electrical Code, Part II. 1.2 This Standard also specifies the requirements for molded-on general-use attachment plugs and cord connectors. 1.3 This Standard also specifies the requirements for molded-on hospital grade attachment plugs and cord connectors. 1.4 This Standard also specifies the requirements for cord restraint devices. 1.5 These requirements do not cover cord sets intended for temporary outdoor use — not to exceed 90 days — with outdoor equipment, Christmas-tree, and other seasonal decorative-lighting outfits. 1.6 This Standard does not cover electric vehicle cord sets. Requirements for electric vehicle cord sets are listed in CSA C22.2 No. 282. 1.7 This Standard does not cover cord reels and power bars. Requirements for cord reels and power bars are listed in CSA C22.2 No. 308. 1.8 This Standard contains the following annexes: a) Annex A — Component standards reference list; b) Annex B — Illustrative definitions; c) Annex C — Canadian marking translations; d) Annex D — Marine shore power sets; e) Annex E — Manufacturing and production tests; and f) Annex F — Marine shore power cable sets. 1.9 In this Standard, "shall" is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; "should" is used to express a recommendation or that which is advised but not required; and "may" is used to express an option or that which is permissible within the limits of the standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application. 1.10 The values given in SI units are the units of record for the purposes of this Standard. The values given in parentheses are for information and comparison only.
Previous Editions
Can’t find what you are looking for?
Please contact us at:
Related Documents
-

CAN/CSA-E60730-2-9:18 (R2023)/A2:24 – Amendment 2:2024 to CAN/CSA-E60730-2-9:18, Automatic electrical controls — Part 2-9: Particular requirements for temperature sensing controls (Adopted amendment 2:2020 to IEC 60730-2-9:2018)
CDN $19.00 Add to cart -

CSA E61558-2-5:25 – Safety of transformers, reactors, power supply units and combinations thereof — Part 2-5: Particular requirements and tests for transformers for shavers, power supply units for shavers and shaver supply units (Adopted IEC 61558-2-5:2024, third edition, 2024-08, with Canadian deviations) | Sécurité des transformateurs, bobines d’inductance, blocs d’alimentation et combinaisons de ces éléments — Partie 2-5 : Exigences particulières et essais pour les transformateurs pour rasoirs, les blocs d’alimentation incorporant un transformateur pour rasoir et les blocs d’alimentation pour rasoirs (norme IEC 61558-2-5:2024 adoptée, troisième édition, 2024-08, avec exigences propres au Canada)
CDN $299.00 Add to cart -

IEEE 844.2-2017/CSA C293.2:17 (R2022) – Skin effect trace heating of pipelines, vessels, equipment, and structures—Application guide for design, installation, testing, commissioning, and maintenance
CDN $158.00 Add to cart -

IEEE 844.1-2017/CSA C22.2 NO. 293.1:17 (R2022) – Skin effect trace heating of pipelines, vessels, equipment, and structures—General, testing, marking, and documentation requirements
CDN $158.00 Add to cart







