
CAN/CSA-C22.2 NO. 60745-2-22-12 (R2022)
CAN/CSA-C22.2 NO. 60745-2-22-12 (R2022) – Hand-held motor-operated electric tools – Safety – Part 2-22: Particular requirements for cut-off machines (Binational standard with UL 60745- 2-22)
CDN $232.00
Hand-held motor-operated electric tools – Safety – Part 2-22: Particular requirements for cut-off machines (Binational standard with UL 60745- 2-22)
Description
Preface This is the harmonized CSA Group and UL standard for Hand-Held Motor-Operated Electric Tools – Safety – Part 2-22: Particular Requirements for Cut-Off Machines. It is the first edition of CAN/CSA C22.2 No. 60745-2-22, and the first edition of UL 60745-2-22. This harmonized standard has been jointly revised on June 19, 2014. For this purpose, CSA Group and UL are issuing revision pages dated June 19, 2014. This harmonized standard is based on IEC Publication 60745-2-22: First edition, Hand-held motor-operated electric tools – Safety – Part 2-22: Particular requirements for cut-off machines issued 03-2011. IEC publication 60745-2-22 is copyrighted by the IEC. This harmonized standard was prepared by the CSA Group and Underwriters Laboratories Inc. (UL). The efforts and support of the Binational Working Group for Adoption of IEC tool standards, are gratefully acknowledged. This standard is considered suitable for use for conformity assessment within the stated scope of the standard. This standard was reviewed by the CSA Subcommittee on Safety of Hand-Held Motor-Operated Electric Tools, under the jurisdiction of the CSA Technical Committee on Consumer and Commercial Products and the CSA Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the CSA Technical Committee. This standard has been approved as a National Standard of Canada by the Standards Council of Canada (SCC). This standard has been approved by the American National Standards Institute (ANSI) as an American National Standard. Scope This clause of Part 1 is applicable as follows: Addition: This standard applies to cut-off machines fitted with – one bonded reinforced wheel of Type 41 or Type 42, or – one or more diamond cut-off wheels with the peripheral gaps, if any, not exceeding 10 mm and with – a rated speed not exceeding a peripheral speed of the wheel of 100 m/s at rated capacity and – a rated wheel capacity range of 55 mm to 410 mm. These machines are intended to cut materials such as metals, concrete, masonry, glass and tile. This standard does not apply to: – grinders, sanders, or polishers, even if they can be converted to a cut-off machine, which are covered by IEC 60745-2-3; – circular saws which are covered by IEC 60745-2-5.
Edition
Not found
Published Date
2026-10-05
Status
Not found
Pages
60
Format 
Secure PDF
Secure – PDF details
- Save your file locally or view it via a web viewer
- Viewing permissions are restricted exclusively to the purchaser
- Device limits - 3
- Printing – Enabled only to print (1) copy
See more about our Environmental Commitment
Abstract
Preface This is the harmonized CSA Group and UL standard for Hand-Held Motor-Operated Electric Tools – Safety – Part 2-22: Particular Requirements for Cut-Off Machines. It is the first edition of CAN/CSA C22.2 No. 60745-2-22, and the first edition of UL 60745-2-22. This harmonized standard has been jointly revised on June 19, 2014. For this purpose, CSA Group and UL are issuing revision pages dated June 19, 2014. This harmonized standard is based on IEC Publication 60745-2-22: First edition, Hand-held motor-operated electric tools – Safety – Part 2-22: Particular requirements for cut-off machines issued 03-2011. IEC publication 60745-2-22 is copyrighted by the IEC. This harmonized standard was prepared by the CSA Group and Underwriters Laboratories Inc. (UL). The efforts and support of the Binational Working Group for Adoption of IEC tool standards, are gratefully acknowledged. This standard is considered suitable for use for conformity assessment within the stated scope of the standard. This standard was reviewed by the CSA Subcommittee on Safety of Hand-Held Motor-Operated Electric Tools, under the jurisdiction of the CSA Technical Committee on Consumer and Commercial Products and the CSA Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the CSA Technical Committee. This standard has been approved as a National Standard of Canada by the Standards Council of Canada (SCC). This standard has been approved by the American National Standards Institute (ANSI) as an American National Standard. Scope This clause of Part 1 is applicable as follows: Addition: This standard applies to cut-off machines fitted with - one bonded reinforced wheel of Type 41 or Type 42, or - one or more diamond cut-off wheels with the peripheral gaps, if any, not exceeding 10 mm and with - a rated speed not exceeding a peripheral speed of the wheel of 100 m/s at rated capacity and - a rated wheel capacity range of 55 mm to 410 mm. These machines are intended to cut materials such as metals, concrete, masonry, glass and tile. This standard does not apply to: - grinders, sanders, or polishers, even if they can be converted to a cut-off machine, which are covered by IEC 60745-2-3; - circular saws which are covered by IEC 60745-2-5.
Previous Editions
Can’t find what you are looking for?
Please contact us at:
Related Documents
-

CSA E61558-2-13:25 – Safety of transformers, reactors, power supply units and combinations thereof — Part 2-13: Particular requirements and tests for auto-transformers and power supply units incorporating auto-transformers for general applications (Adopted IEC 61558-2-13:2022, third edition, 2022-10, with Canadian deviations) | Sécurité des transformateurs, bobines d’inductance, blocs d’alimentation et combinaisons de ces éléments — Partie 2-13 : Exigences particulières et essais pour les autotransformateurs et les blocs d’alimentation qui incorporent des autotransformateurs pour applications d’ordre général (norme IEC 61558-2-13:2022 adoptée, troisième édition, 2022-10, avec exigences propres au Canada)
CDN $205.00 Add to cart -

CSA SPE-3000:19 – Model code for the field evaluation of medical electrical equipment (MEE) and medical electrical systems (MES)
CDN $334.00 Add to cart -

IEEE 844.3-2019/CSA C22.2 NO. 293.3:19 (R2024) – Impedance heating of pipelines and equipment—General, testing, marking, and documentation requirements
CDN $174.00 Add to cart -

CSA E60825-1:15 (R2025) – Safety of laser products — Part 1: Equipment classification and requirements (Adopted IEC 60825-1:2014, third edition, 2014-05, with Canadian deviations) | Sécurité des appareils à laser — Partie 1 : Classification des matériels et exigences (norme IEC 60825-1:2014 adoptée, troisième édition, 2014-05, avec exigences propres au Canada)
CDN $488.00 Add to cart







