
CSA/ANSI C22.2 NO. 298:26
CSA/ANSI C22.2 NO. 298:26 – High-voltage couplers
CDN $897.00
High-voltage couplers
Description
Preface This is the third edition of CSA/ANSI C22.2 No. 298, High-voltage couplers . It supersedes the previous editions published in 2021 and 2016. It is one of a series of Standards issued under Part II of the Canadian Electrical Code. This Standard is considered suitable for use for conformity assessment within the stated scope of the Standard. This Standard was prepared by the Subcommittee on High-Voltage Couplers, under the jurisdiction of the Technical Committee on Wiring Products and the Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the Technical Committee. This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group. This Standard has been approved by the American National Standards Institute (ANSI) as an American National Standard. Scope 1.1 This Standard applies to locking-type, pin and sleeve-type plugs, receptacles, power inlets, connectors, junction boxes, and live-end covers rated up to 1200 A (for single- and multi-pole) and above 750 V to 35 kV ac, 50/60 Hz, or up to 1500 V dc and which shall have one or more pilot contacts for multi-pole configuration and above 750 V to 1000 V ac or dc for single-pole configuration. These devices are intended to provide portable power from branch circuits, or are for direct connection to the branch circuit in accordance with the Canadian Electrical Code, Part I, or the National Electrical Code (NEC) using portable power cables with copper conductors, for use in either indoor or outdoor, nonhazardous or hazardous locations. 1.2 The products covered in this Standard are commonly, but not exclusively, used in the following applications: a) open pit mining; b) underground mining; c) tunneling; d) shore to ship power; e) portable power equipment; f) general industrial use; and g) drilling. 1.3 This Standard applies to locking-type, pin and sleeve-type plugs, receptacles, power inlets, connectors, junction boxes, and live-end covers, intended to operate up to and including an ambient temperature of 40 °C. Temperatures above 40 °C are subject to additional investigation. 1.4 This Standard does not apply to a) products covered in CSA C22.2 No. 182.1 and UL 1682; b) devices intended to be separated or connected under load; and c) products covered in CAN/CSA-C22.2 No. 282 and UL 2251. 1.5 The values given in SI units are the units of record for the purposes of this Standard. The values given in parentheses are for information and comparison only. 1.6 In this Standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the Standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the Standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.
Edition
Not found
Published Date
2026-10-05
Status
Not found
Pages
88
Format 
Secure PDF
Secure – PDF details
- Save your file locally or view it via a web viewer
- Viewing permissions are restricted exclusively to the purchaser
- Device limits - 3
- Printing – Enabled only to print (1) copy
See more about our Environmental Commitment
Abstract
Preface This is the third edition of CSA/ANSI C22.2 No. 298, High-voltage couplers . It supersedes the previous editions published in 2021 and 2016. It is one of a series of Standards issued under Part II of the Canadian Electrical Code. This Standard is considered suitable for use for conformity assessment within the stated scope of the Standard. This Standard was prepared by the Subcommittee on High-Voltage Couplers, under the jurisdiction of the Technical Committee on Wiring Products and the Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the Technical Committee. This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group. This Standard has been approved by the American National Standards Institute (ANSI) as an American National Standard. Scope 1.1 This Standard applies to locking-type, pin and sleeve-type plugs, receptacles, power inlets, connectors, junction boxes, and live-end covers rated up to 1200 A (for single- and multi-pole) and above 750 V to 35 kV ac, 50/60 Hz, or up to 1500 V dc and which shall have one or more pilot contacts for multi-pole configuration and above 750 V to 1000 V ac or dc for single-pole configuration. These devices are intended to provide portable power from branch circuits, or are for direct connection to the branch circuit in accordance with the Canadian Electrical Code, Part I, or the National Electrical Code (NEC) using portable power cables with copper conductors, for use in either indoor or outdoor, nonhazardous or hazardous locations. 1.2 The products covered in this Standard are commonly, but not exclusively, used in the following applications: a) open pit mining; b) underground mining; c) tunneling; d) shore to ship power; e) portable power equipment; f) general industrial use; and g) drilling. 1.3 This Standard applies to locking-type, pin and sleeve-type plugs, receptacles, power inlets, connectors, junction boxes, and live-end covers, intended to operate up to and including an ambient temperature of 40 °C. Temperatures above 40 °C are subject to additional investigation. 1.4 This Standard does not apply to a) products covered in CSA C22.2 No. 182.1 and UL 1682; b) devices intended to be separated or connected under load; and c) products covered in CAN/CSA-C22.2 No. 282 and UL 2251. 1.5 The values given in SI units are the units of record for the purposes of this Standard. The values given in parentheses are for information and comparison only. 1.6 In this Standard, "shall" is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the Standard; "should" is used to express a recommendation or that which is advised but not required; and "may" is used to express an option or that which is permissible within the limits of the Standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.
Previous Editions
Can’t find what you are looking for?
Please contact us at:
Related Documents
-

CSA E61951-1:21 (R2026) – Secondary cells and batteries containing alkaline or other non-acid electrolytes — Secondary sealed cells and batteries for portable applications — Part 1: Nickel-cadmium (Adopted IEC 61951:2017, fourth edition, 2017-03, with Canadian deviations) | Accumulateurs alcalins et autres accumulateurs à électrolyte non acide — Accumulateurs étanches pour applications portables — Partie 1 : Nickel-cadmium (norme IEC 61951-1:2017 adoptée, quatrième édition, 2017-03), avec exigences propres au Canada)
CDN $527.00 Add to cart -

CSA C22.3 NO. 5.1:93 (R2022) – Recommended practices for electrical protection – Electric contact between overhead supply and communication lines
CDN $149.00 Add to cart -

CSA E61347-2-3:23 – Lamp control gear — Part 2-3: Particular requirements for a.c. and/or d.c. supplied electronic control gear for fluorescent lamps (Adopted IEC 61347-2-3:2011, edition 2:2011 consolidated with amendment 1:2016, with Canadian deviations) | Appareillages de lampes — Partie 2-3 : Exigences particulières pour les appareillages électroniques alimentés en courant alternatif et/ou en courant continu pour lampes fluorescentes (norme IEC 61347-2-3:2011 adoptée, édition 2:2011 consolidée par l’amendement 1:2016, avec exigences propres au Canada)
CDN $620.00 Add to cart -

CSA E60825-1:15 (R2025) – Safety of laser products — Part 1: Equipment classification and requirements (Adopted IEC 60825-1:2014, third edition, 2014-05, with Canadian deviations) | Sécurité des appareils à laser — Partie 1 : Classification des matériels et exigences (norme IEC 60825-1:2014 adoptée, troisième édition, 2014-05, avec exigences propres au Canada)
CDN $488.00 Add to cart







