
CSA C22.2 NO. 156:M87 (R2023)
CSA C22.2 NO. 156:M87 (R2023) – Solid-State Speed Controls
CDN $134.00
Solid-State Speed Controls
Description
Preface This is the first edition of No. 156 of a series of Standards issued by Canadian Standards Association under Part II of the Canadian Electrical Code. It is written in SI (metric) units. This Standard applies to solid-state, single-phase motor speed controls for use in nonhazardous locations, and for installation in accordance with the Rules of the Canadian Electrical Code, Part I. This edition incorporates Electrical Bulletin No. 1207, Requirements for Solid State Speed Control Switches, January 3, 1979. For general information on Standards of the Canadian Electrical Code, Part II, see the Preface of CSA Standard C22.2 No. 0, General Requirements—Canadian Electrical Code, Part II. This Standard was prepared by a Subcommittee of the Technical Committee on Industrial Products under the jurisdiction of the Standards Steering Committee on Canadian Electrical Code, Part II, and was formally approved by these Committees. Scope 1.1 This Standard applies to solid-state, single-phase motor speed controls, rated at 300 V and less, 20 A and less, designed to be used in circuits for the control of shaded pole, permanent split capacitor, or universal motors, and other motors suitable for use with this type of control, intended for use in nonhazardous locations in accordance with the Canadian Electrical Code, Part I. 1.2 This Standard applies to controls that may incorporate a switch to place an air gap in series with the motor; and when provided with a series switch, (a) incorporate solid-state components in a phase shift network to provide a controlled voltage output and designed so that (i) Type I: the ON/OFF function is independent of the output voltage setting; or (ii) Type II: the ON/OFF function can be operated at minimum output voltage setting only; or (iii) Type III: the ON/OFF function can be operated at maximum output voltage setting only; or (b) (Type IV) incorporate solid-state components to provide one or more, but not an infinite number of positions of control. 1.3 This Standard applies to controls intended for (a) flush mounting; (b) surface mounting; (c) use as a table-mounted control to which a portable motor can be temporarily connected; (d) installation in other equipment as part of the control package for that equipment; (e) permanent installation in the supply line of a motor; or (f) other similar applications within the general outline above. 1.4 This Standard does not apply to resistor, transformer, and variable frequency type motor speed controls.
Edition
Not found
Published Date
2026-10-05
Status
Not found
Pages
28
Format 
Secure PDF
Secure – PDF details
- Save your file locally or view it via a web viewer
- Viewing permissions are restricted exclusively to the purchaser
- Device limits - 3
- Printing – Enabled only to print (1) copy
See more about our Environmental Commitment
Abstract
Preface This is the first edition of No. 156 of a series of Standards issued by Canadian Standards Association under Part II of the Canadian Electrical Code. It is written in SI (metric) units. This Standard applies to solid-state, single-phase motor speed controls for use in nonhazardous locations, and for installation in accordance with the Rules of the Canadian Electrical Code, Part I. This edition incorporates Electrical Bulletin No. 1207, Requirements for Solid State Speed Control Switches, January 3, 1979. For general information on Standards of the Canadian Electrical Code, Part II, see the Preface of CSA Standard C22.2 No. 0, General Requirements—Canadian Electrical Code, Part II. This Standard was prepared by a Subcommittee of the Technical Committee on Industrial Products under the jurisdiction of the Standards Steering Committee on Canadian Electrical Code, Part II, and was formally approved by these Committees. Scope 1.1 This Standard applies to solid-state, single-phase motor speed controls, rated at 300 V and less, 20 A and less, designed to be used in circuits for the control of shaded pole, permanent split capacitor, or universal motors, and other motors suitable for use with this type of control, intended for use in nonhazardous locations in accordance with the Canadian Electrical Code, Part I. 1.2 This Standard applies to controls that may incorporate a switch to place an air gap in series with the motor; and when provided with a series switch, (a) incorporate solid-state components in a phase shift network to provide a controlled voltage output and designed so that (i) Type I: the ON/OFF function is independent of the output voltage setting; or (ii) Type II: the ON/OFF function can be operated at minimum output voltage setting only; or (iii) Type III: the ON/OFF function can be operated at maximum output voltage setting only; or (b) (Type IV) incorporate solid-state components to provide one or more, but not an infinite number of positions of control. 1.3 This Standard applies to controls intended for (a) flush mounting; (b) surface mounting; (c) use as a table-mounted control to which a portable motor can be temporarily connected; (d) installation in other equipment as part of the control package for that equipment; (e) permanent installation in the supply line of a motor; or (f) other similar applications within the general outline above. 1.4 This Standard does not apply to resistor, transformer, and variable frequency type motor speed controls.
Previous Editions
Can’t find what you are looking for?
Please contact us at:
Related Documents
-

CSA E61347-2-3:23 – Lamp control gear — Part 2-3: Particular requirements for a.c. and/or d.c. supplied electronic control gear for fluorescent lamps (Adopted IEC 61347-2-3:2011, edition 2:2011 consolidated with amendment 1:2016, with Canadian deviations) | Appareillages de lampes — Partie 2-3 : Exigences particulières pour les appareillages électroniques alimentés en courant alternatif et/ou en courant continu pour lampes fluorescentes (norme IEC 61347-2-3:2011 adoptée, édition 2:2011 consolidée par l’amendement 1:2016, avec exigences propres au Canada)
CDN $620.00 Add to cart -

CSA E62660-1:21 (R2026) – Secondary lithium-ion cells for the propulsion of electric road vehicles – Part 1: Performance testing (Adopted IEC 62660-1:2018, second edition, 2018-12, with Canadian deviations) | Éléments d’accumulateurs lithium-ion pour la propulsion des véhicules routiers électriques – Partie 1 : Essais de performance (norme IEC 62660-1:2018 adoptée, deuxième édition, 2018-12, avec exigences propres au Canada)
CDN $436.00 Add to cart -

CSA E60825-1:15 (R2025) – Safety of laser products — Part 1: Equipment classification and requirements (Adopted IEC 60825-1:2014, third edition, 2014-05, with Canadian deviations) | Sécurité des appareils à laser — Partie 1 : Classification des matériels et exigences (norme IEC 60825-1:2014 adoptée, troisième édition, 2014-05, avec exigences propres au Canada)
CDN $488.00 Add to cart -

CAN/CSA-E60730-2-9:18 (R2023)/A2:24 – Amendment 2:2024 to CAN/CSA-E60730-2-9:18, Automatic electrical controls — Part 2-9: Particular requirements for temperature sensing controls (Adopted amendment 2:2020 to IEC 60730-2-9:2018)
CDN $19.00 Add to cart







