
CSA C22.2 NO. 269.5:17 (R2022)
CSA C22.2 NO. 269.5:17 (R2022) – Surge protective devices – Type 5 – Components
CDN $213.00
Surge protective devices – Type 5 – Components
Description
Preface This is the second edition of CSA C22.2 No. 269.5, Surge protective devices Type 5 — Components. It supersedes the previous edition published in 2014. This Standard is one of a series of standards dealing with surge protective devices. This Standard is issued by CSA Group under Part II of the Canadian Electrical Code. For general information on the Standards of the Canadian Electrical Code, Part II, see the Preface of CAN/CSA-C22.2 No. 0. The previous edition was written with the intent that the components tested to the requirements of this Standard were intended for use within a Type 1, Type 2, or Type 3 SPD device. This new edition was updated to allow for the testing and certification of components that might not necessarily be destined for use within an SPD device, but may instead be used within the circuitry of a domestic appliance or other such equipment. This edition also includes a new test section for thermal protective devices, a provision to allow the manufacturer to specify nominal discharge current levels, and numerous other minor updates throughout. This Standard is considered suitable for use for conformity assessment within the stated scope of the Standard. This Standard was prepared by the Subcommittee on Surge Protective Devices, under the jurisdiction of the Technical Committee on Industrial Products and the Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the Technical Committee. This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group. Scope 1.1 This Standard applies to surge protective device (SPD) components designed to mitigate the effects of transient overvoltages and surge events and intended for use in surge protective devices (SPDs) or in non-SPD applications. 1.2 SPD Components containing integral thermal devices are within the scope of this Standard. 1.3 Components include but are not limited to metal oxide varistors (MOVs), silicon avalanche diodes (SADs), spark gaps (open or sealed type), and gas discharge tubes (GDT). 1.4 This Standard does not apply to products that are combinations of components nor to assemblies that use these components as covered in CSA C22.2 No. 269.4. 1.5 Components such as inductors or capacitors and other essentially linear components are not considered SPDs. 1.6 The values given in SI units are the units of record for the purposes of this Standard. The values given in parentheses are for information and comparison only. 1.7 In this Standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (nonmandatory) to define their application.
Edition
Not found
Published Date
2026-10-05
Status
Not found
Pages
30
Format 
Secure PDF
Secure – PDF details
- Save your file locally or view it via a web viewer
- Viewing permissions are restricted exclusively to the purchaser
- Device limits - 3
- Printing – Enabled only to print (1) copy
See more about our Environmental Commitment
Abstract
Preface This is the second edition of CSA C22.2 No. 269.5, Surge protective devices Type 5 — Components. It supersedes the previous edition published in 2014. This Standard is one of a series of standards dealing with surge protective devices. This Standard is issued by CSA Group under Part II of the Canadian Electrical Code. For general information on the Standards of the Canadian Electrical Code, Part II, see the Preface of CAN/CSA-C22.2 No. 0. The previous edition was written with the intent that the components tested to the requirements of this Standard were intended for use within a Type 1, Type 2, or Type 3 SPD device. This new edition was updated to allow for the testing and certification of components that might not necessarily be destined for use within an SPD device, but may instead be used within the circuitry of a domestic appliance or other such equipment. This edition also includes a new test section for thermal protective devices, a provision to allow the manufacturer to specify nominal discharge current levels, and numerous other minor updates throughout. This Standard is considered suitable for use for conformity assessment within the stated scope of the Standard. This Standard was prepared by the Subcommittee on Surge Protective Devices, under the jurisdiction of the Technical Committee on Industrial Products and the Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the Technical Committee. This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group. Scope 1.1 This Standard applies to surge protective device (SPD) components designed to mitigate the effects of transient overvoltages and surge events and intended for use in surge protective devices (SPDs) or in non-SPD applications. 1.2 SPD Components containing integral thermal devices are within the scope of this Standard. 1.3 Components include but are not limited to metal oxide varistors (MOVs), silicon avalanche diodes (SADs), spark gaps (open or sealed type), and gas discharge tubes (GDT). 1.4 This Standard does not apply to products that are combinations of components nor to assemblies that use these components as covered in CSA C22.2 No. 269.4. 1.5 Components such as inductors or capacitors and other essentially linear components are not considered SPDs. 1.6 The values given in SI units are the units of record for the purposes of this Standard. The values given in parentheses are for information and comparison only. 1.7 In this Standard, "shall" is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; "should" is used to express a recommendation or that which is advised but not required; and "may" is used to express an option or that which is permissible within the limits of the standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (nonmandatory) to define their application.
Previous Editions
Can’t find what you are looking for?
Please contact us at:
Related Documents
-

IEEE 844.4-2019/CSA C293.4:19 (R2024) – Impedance heating of pipelines and equipment—Application guide for design, installation, testing, commissioning, and maintenance
CDN $174.00 Add to cart -

CAN/CSA-E60730-2-9:18 (R2023)/A2:24 – Amendment 2:2024 to CAN/CSA-E60730-2-9:18, Automatic electrical controls — Part 2-9: Particular requirements for temperature sensing controls (Adopted amendment 2:2020 to IEC 60730-2-9:2018)
CDN $19.00 Add to cart -

CSA E61558-2-13:25 – Safety of transformers, reactors, power supply units and combinations thereof — Part 2-13: Particular requirements and tests for auto-transformers and power supply units incorporating auto-transformers for general applications (Adopted IEC 61558-2-13:2022, third edition, 2022-10, with Canadian deviations) | Sécurité des transformateurs, bobines d’inductance, blocs d’alimentation et combinaisons de ces éléments — Partie 2-13 : Exigences particulières et essais pour les autotransformateurs et les blocs d’alimentation qui incorporent des autotransformateurs pour applications d’ordre général (norme IEC 61558-2-13:2022 adoptée, troisième édition, 2022-10, avec exigences propres au Canada)
CDN $205.00 Add to cart -

CSA TS-117:23 – National technical specification for terminology for the decentralized energy industry in Canada
CDN $79.00 Add to cart







