
CSA C22.2 NO. 33:23
CSA C22.2 NO. 33:23 – Electrical safety requirements for cranes and hoists
CDN $205.00
Electrical safety requirements for cranes and hoists
Description
Preface This is the fifth edition of CSA C22.2 No. 33, Electrical safety requirements for cranes and hoists , one of a series of Standards issued by CSA Group under Part II of the Canadian Electrical Code. It supersedes the previous editions published in 2019, 1984, 1959, and 1936. The major changes to this edition include the following: a) updated construction requirements for incoming service and feeders; b) changes to special construction requirements for monorail hoists separate from cranes; c) addition of the mould stress relief test for conductor bar systems; and d) added normative Annex A. This Standard is considered suitable for use for conformity assessment within the stated scope of the Standard. This Standard was prepared by the Subcommittee on Electric Cranes and Hoists, under the jurisdiction of the Technical Committee on Industrial Products and the Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the Technical Committee. This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group. Scope 1.1 This Standard applies to all types of electric cranes, including electric overhead travelling cranes, and hoists for vertical lifting and lowering of freely suspended load for voltages of 750 V and less between conductors. The equipment specified in this Standard is intended for installation in accordance with the Canadian Electrical Code, Part I. 1.2 This Standard applies to the following cranes and hoists electrification systems: a) bare, non-rigid and rigid contact conductors, collector shoes and wheels, and associated fittings; and b) insulated conductor bar assemblies, collector trolley assemblies, and associated fittings (such as splices, power feeds, hangers, end caps, and similar). 1.3 This Standard applies to equipment for general industrial and commercial application, in nonhazardous locations for indoor and outdoor locations. 1.4 This Standard applies to equipment for installation in an ambient temperature not exceeding 40 °C. 1.5 This Standard applies to wireless control equipment used in conjunction with electric cranes and hoists. 1.6 Annex B covers optional requirements for DC drives. Annex C covers optional requirements for contact conductors. 1.7 This Standard does not apply to a) elevators; b) dumbwaiters; c) stairway hoists; d) tower cranes; e) manually operated chain driven cranes; f) mobile cranes; g) draglines; h) mine hoists; i) guided loads; j) below-the-hook attachments; and k) construction cranes and hoists. 1.8 In this Standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the Standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the Standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.
Edition
Not found
Published Date
2026-10-05
Status
Not found
Pages
46
Format 
Secure PDF
Secure – PDF details
- Save your file locally or view it via a web viewer
- Viewing permissions are restricted exclusively to the purchaser
- Device limits - 3
- Printing – Enabled only to print (1) copy
See more about our Environmental Commitment
Abstract
Preface This is the fifth edition of CSA C22.2 No. 33, Electrical safety requirements for cranes and hoists , one of a series of Standards issued by CSA Group under Part II of the Canadian Electrical Code. It supersedes the previous editions published in 2019, 1984, 1959, and 1936. The major changes to this edition include the following: a) updated construction requirements for incoming service and feeders; b) changes to special construction requirements for monorail hoists separate from cranes; c) addition of the mould stress relief test for conductor bar systems; and d) added normative Annex A. This Standard is considered suitable for use for conformity assessment within the stated scope of the Standard. This Standard was prepared by the Subcommittee on Electric Cranes and Hoists, under the jurisdiction of the Technical Committee on Industrial Products and the Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the Technical Committee. This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group. Scope 1.1 This Standard applies to all types of electric cranes, including electric overhead travelling cranes, and hoists for vertical lifting and lowering of freely suspended load for voltages of 750 V and less between conductors. The equipment specified in this Standard is intended for installation in accordance with the Canadian Electrical Code, Part I. 1.2 This Standard applies to the following cranes and hoists electrification systems: a) bare, non-rigid and rigid contact conductors, collector shoes and wheels, and associated fittings; and b) insulated conductor bar assemblies, collector trolley assemblies, and associated fittings (such as splices, power feeds, hangers, end caps, and similar). 1.3 This Standard applies to equipment for general industrial and commercial application, in nonhazardous locations for indoor and outdoor locations. 1.4 This Standard applies to equipment for installation in an ambient temperature not exceeding 40 °C. 1.5 This Standard applies to wireless control equipment used in conjunction with electric cranes and hoists. 1.6 Annex B covers optional requirements for DC drives. Annex C covers optional requirements for contact conductors. 1.7 This Standard does not apply to a) elevators; b) dumbwaiters; c) stairway hoists; d) tower cranes; e) manually operated chain driven cranes; f) mobile cranes; g) draglines; h) mine hoists; i) guided loads; j) below-the-hook attachments; and k) construction cranes and hoists. 1.8 In this Standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the Standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the Standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.
Previous Editions
Can’t find what you are looking for?
Please contact us at:
Related Documents
-

CSA TS-117:23 – National technical specification for terminology for the decentralized energy industry in Canada
CDN $79.00 Add to cart -

CSA SPE-1000:25 – Model Code for the field evaluation of electrical equipment
CDN $378.00 Add to cart -

CSA E62660-2:21 (R2026) – Secondary lithium-ion cells for the propulsion of electric road vehicles – Part 2: Reliability and abuse testing (Adopted IEC 62660-2:2018, second edition, 2018-12, with Canadian deviations) | Éléments d’accumulateurs lithium-ion pour la propulsion des véhicules routiers électriques – Partie 2 : Essais de fiabilité et de traitement abusif (norme IEC 62660-2:2018 adoptée, deuxième édition, 2018-12, avec exigences propres au Canada)
CDN $225.00 Add to cart -

CAN/CSA-E61558-1:12 (R2022) – Safety of power transformers, power supplies, reactors and similar products – Part 1: General requirements and tests (Adopted IEC 61558- 1:1997 + A1:1998, edition 2.1, 2009-04 with Canadian deviations) | Sécurité des transformateurs, alimentations, bobines d’inductance et produits analogues – Partie 1: Exigences générales et essais (norme CEI 61558-1:1997 + A1:1998 adoptée, édition 2.1, 2009-04 avec exigences propres au Canada)
CDN $630.00 Add to cart







