
CSA C22.2 NO. 745-2-31:95 (R2023)
CSA C22.2 NO. 745-2-31:95 (R2023) – Safety of portable electric tools – Part 2: Particular Requirements for diamond core drills (Binational standard with UL 745-2-31)
CDN $420.00
Safety of portable electric tools – Part 2: Particular Requirements for diamond core drills (Binational standard with UL 745-2-31)
Description
Preface This is the common CSA and UL Standard for portable electric diamond core drills. It is the first edition of CSA Standard CANICSA-C22.2 No. 745-2-31, Safety of portable electric tools — Part 2: Particular requirements for diamond core drills and UL 745-2-31, Safety of portable electric tools — Part. 2: Particular requirements for diamond core drills. It is written in SI (metric) units. It will coexist with the CSA Standard CAN/CSA-C22.2 No. 71.1 for the period given in CSA Certification Notice — Electrical Tools No. 6. This Standard was prepared by the Canadian Standards Association and Underwriters Laboratories Inc. It contains particular requirements and is intended to be used in conjunction with the general Standard CAN/CSA-C22.2 No. 745-1/UL 745-1. Where a clause of the general Standard (CAN/CSA-C22.2 No. 745-1/UL 745-1) is not mentioned in this Standard, the clause applies as far as is reasonable. Where this particular Standard states addition, modification, or replacement, the relevant requirement, test specification, or explanatory matter in the general Standard (CAN/CSA-C22.2 No. 745-1/UL 745-1) should be adapted accordingly. If the functions of a tool are covered by different particular Standards, the relevant particular Standard is applied to each function separately, so far as is reasonable. If applicable, the influence of one function on the other is taken into account. This Standard was reviewed by the CSA Subcommittee on Portable Electric Tools of the Technical Committee on Consumer and Commercial Products under the jurisdiction of the Standards Steering Committee on the Canadian Electrical Code, Part Il, and was formally approved by these Committees. This Standard was processed and reviewed in accordance with the method of development, revision, and implementation of UL Standards for safety. This Standard has been approved by the Standards Council of Canada as a National Standard of Canada and it will be submitted to the American National Standards Institute (ANSI) for publication as an American National Standard. Scope This clause of Part 1 is applicable, except as follows: 1.1 Replacement: This standard applies to diamond core drills.
Edition
Not found
Published Date
2026-10-05
Status
Not found
Pages
25
Format 
Secure PDF
Secure – PDF details
- Save your file locally or view it via a web viewer
- Viewing permissions are restricted exclusively to the purchaser
- Device limits - 3
- Printing – Enabled only to print (1) copy
See more about our Environmental Commitment
Abstract
Preface This is the common CSA and UL Standard for portable electric diamond core drills. It is the first edition of CSA Standard CANICSA-C22.2 No. 745-2-31, Safety of portable electric tools — Part 2: Particular requirements for diamond core drills and UL 745-2-31, Safety of portable electric tools — Part. 2: Particular requirements for diamond core drills. It is written in SI (metric) units. It will coexist with the CSA Standard CAN/CSA-C22.2 No. 71.1 for the period given in CSA Certification Notice — Electrical Tools No. 6. This Standard was prepared by the Canadian Standards Association and Underwriters Laboratories Inc. It contains particular requirements and is intended to be used in conjunction with the general Standard CAN/CSA-C22.2 No. 745-1/UL 745-1. Where a clause of the general Standard (CAN/CSA-C22.2 No. 745-1/UL 745-1) is not mentioned in this Standard, the clause applies as far as is reasonable. Where this particular Standard states addition, modification, or replacement, the relevant requirement, test specification, or explanatory matter in the general Standard (CAN/CSA-C22.2 No. 745-1/UL 745-1) should be adapted accordingly. If the functions of a tool are covered by different particular Standards, the relevant particular Standard is applied to each function separately, so far as is reasonable. If applicable, the influence of one function on the other is taken into account. This Standard was reviewed by the CSA Subcommittee on Portable Electric Tools of the Technical Committee on Consumer and Commercial Products under the jurisdiction of the Standards Steering Committee on the Canadian Electrical Code, Part Il, and was formally approved by these Committees. This Standard was processed and reviewed in accordance with the method of development, revision, and implementation of UL Standards for safety. This Standard has been approved by the Standards Council of Canada as a National Standard of Canada and it will be submitted to the American National Standards Institute (ANSI) for publication as an American National Standard. Scope This clause of Part 1 is applicable, except as follows: 1.1 Replacement: This standard applies to diamond core drills.
Previous Editions
Can’t find what you are looking for?
Please contact us at:
Related Documents
-

CSA E61558-2-13:25 – Safety of transformers, reactors, power supply units and combinations thereof — Part 2-13: Particular requirements and tests for auto-transformers and power supply units incorporating auto-transformers for general applications (Adopted IEC 61558-2-13:2022, third edition, 2022-10, with Canadian deviations) | Sécurité des transformateurs, bobines d’inductance, blocs d’alimentation et combinaisons de ces éléments — Partie 2-13 : Exigences particulières et essais pour les autotransformateurs et les blocs d’alimentation qui incorporent des autotransformateurs pour applications d’ordre général (norme IEC 61558-2-13:2022 adoptée, troisième édition, 2022-10, avec exigences propres au Canada)
CDN $205.00 Add to cart -

IEEE 844.3-2019/CSA C22.2 NO. 293.3:19 (R2024) – Impedance heating of pipelines and equipment—General, testing, marking, and documentation requirements
CDN $174.00 Add to cart -

CSA E62660-1:21 (R2026) – Secondary lithium-ion cells for the propulsion of electric road vehicles – Part 1: Performance testing (Adopted IEC 62660-1:2018, second edition, 2018-12, with Canadian deviations) | Éléments d’accumulateurs lithium-ion pour la propulsion des véhicules routiers électriques – Partie 1 : Essais de performance (norme IEC 62660-1:2018 adoptée, deuxième édition, 2018-12, avec exigences propres au Canada)
CDN $436.00 Add to cart -

CAN/CSA-E60730-2-9:18 (R2023) – Automatic electrical controls — Part 2-9: Particular requirements for temperature sensing controls (Adopted IEC 60730-2-9:2018, edition 4:2015 consolidated with amendment 1:2018, with Canadian deviations)
CDN $944.00 Add to cart







