Sky Bear Technical Standards - Home
Search
×
FR

Placeholder headline

This is just a placeholder headline

B51-14 (R2019) – Boiler, pressure vessel, and pressure piping code

$

362

BUY NOW

Z259.12-16 (R2026)

Z259.12-16 (R2026) – Connecting components for personal fall-arrest systems (PFAS)

CDN $181.00

Connecting components for personal fall-arrest systems (PFAS)

SKU: 2424365 Categories: ,

Description

Preface This is the third edition of CSA Z259.12, Connecting components for personal fall-arrest systems (PFAS). It supersedes the previous editions, published in 2011 and 2001. This Standard is part of a series of Standards on components of fall-protection systems and provides performance requirements, test methods, and requirements for marking individual components used as part of a personal fall-arrest system. Changes to this edition include a) updates to definitions and figures; b) revision to soft loop testing procedure; c) revisions to the marking requirements; and d) addition of requirements for transverse body loading (both static and dynamic). CSA Group acknowledges that the development of this Standard was made possible, in part, by the financial support of the Canadian government departments responsible for occupational health and safety. This Standard was prepared by the Subcommittee on Connecting Components, under the jurisdiction of the Technical Committee on Fall Protection and the Strategic Steering Committee on Occupational Health and Safety, and has been formally approved by the Technical Committee. This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group. Scope 1.1 This Standard specifies design and performance requirements, test methods, and requirements for marking and labelling individual connecting components used as part of a personal fall-arrest system (PFAS). This Standard applies to components that are a) used in the interconnection of a complete PFAS unit in accordance with the applicable CSA Z259 series of standards; b) intended to be used as the primary single link to a permanent anchorage connector; or c) intended to be used as a primary attachment point between two or more subsystems. 1.2 This Standard does not apply to anchorage connectors that are covered under CAN/CSA-Z259.15. 1.3 In this Standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the Standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the Standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application. 1.4 The values given in SI units are the units of record for the purposes of this Standard. The values given in parentheses are for information and comparison only.

Edition

Not found

Published Date

2026-10-05

Status

Not found

Pages

52

Language Detail Icon

English

Format Secure Icon

Secure PDF

Abstract

Preface This is the third edition of CSA Z259.12, Connecting components for personal fall-arrest systems (PFAS). It supersedes the previous editions, published in 2011 and 2001. This Standard is part of a series of Standards on components of fall-protection systems and provides performance requirements, test methods, and requirements for marking individual components used as part of a personal fall-arrest system. Changes to this edition include a) updates to definitions and figures; b) revision to soft loop testing procedure; c) revisions to the marking requirements; and d) addition of requirements for transverse body loading (both static and dynamic). CSA Group acknowledges that the development of this Standard was made possible, in part, by the financial support of the Canadian government departments responsible for occupational health and safety. This Standard was prepared by the Subcommittee on Connecting Components, under the jurisdiction of the Technical Committee on Fall Protection and the Strategic Steering Committee on Occupational Health and Safety, and has been formally approved by the Technical Committee. This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group. Scope 1.1 This Standard specifies design and performance requirements, test methods, and requirements for marking and labelling individual connecting components used as part of a personal fall-arrest system (PFAS). This Standard applies to components that are a) used in the interconnection of a complete PFAS unit in accordance with the applicable CSA Z259 series of standards; b) intended to be used as the primary single link to a permanent anchorage connector; or c) intended to be used as a primary attachment point between two or more subsystems. 1.2 This Standard does not apply to anchorage connectors that are covered under CAN/CSA-Z259.15. 1.3 In this Standard, "shall" is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the Standard; "should" is used to express a recommendation or that which is advised but not required; and "may" is used to express an option or that which is permissible within the limits of the Standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application. 1.4 The values given in SI units are the units of record for the purposes of this Standard. The values given in parentheses are for information and comparison only.

Previous Editions

Can’t find what you are looking for?

Please contact us at: