
CSA C22.2 NO. 62841-4-4:21 (R2026)
CSA C22.2 NO. 62841-4-4:21 (R2026) – Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery — Safety — Part 4-4: Particular requirements for lawn trimmers, lawn edge trimmers, grass trimmers, brush cutters and brush saws (Binational standard with UL 62841-4-4)
CDN $704.00
Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery — Safety — Part 4-4: Particular requirements for lawn trimmers, lawn edge trimmers, grass trimmers, brush cutters and brush saws (Binational standard with UL 62841-4-4)
Description
Preface This is the harmonized CSA Group and ULSE standard for Electric Motor-Operated Hand-Held Tools, Transportable Tools and Lawn and Garden Machinery – Safety – Part 4-4: Particular Requirements for Lawn Trimmers, Lawn Edge Trimmers, Grass Trimmers, Brush Cutters and Brush Saws. It is the First edition of CSA C22.2 No. 62841-4-4, and the First edition of UL 62841-4-4. This harmonized standard has been jointly revised on August 2, 2024. For this purpose, CSA Group and ULSE are issuing revision pages dated August 2, 2024. This harmonized standard is based on IEC Publication 62841-4-4: First edition, Electric Motor-Operated Hand-Held Tools, Transportable Tools and Lawn and Garden Machinery – Safety – Part 4-4: Particular Requirements for Lawn Trimmers, Lawn Edge Trimmers, Grass Trimmers, Brush Cutters and Brush Saws issued November 2020. IEC publication 62841-4-4 is copyrighted by the IEC. This harmonized standard was prepared by CSA Group and ULSE. The efforts and support of the International Harmonization Committee (IHC) for the adoption of the IEC series of Standards for Hand-Held, Motor-Operated, and Transportable Tools and Lawn and Garden Machinery UL are gratefully acknowledged. This standard is considered suitable for use for conformity assessment within the stated scope of the standard. This standard was reviewed by the CSA Subcommittee on Safety of Hand-Held Motor-Operated Electric Tools, under the jurisdiction of the CSA Technical Committee on Consumer and Commercial Products and the CSA Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the CSA Technical Committee. This standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group. Scope This clause of Part 1 is applicable, except as follows: Addition: This document applies to hand-held and walk-behind lawn trimmers and lawn edge trimmers, used by a standing operator for cutting grass, weeds or similar soft vegetation, and grass trimmers, brush cutters and brush saws used by a standing operator for cutting grass, weeds, brush, bushes, saplings and similar vegetation. This document does not apply to – hand-held machines having a mass of 18 kg or greater; – self-propelled lawn trimmers or lawn edge trimmers; – scissors type lawn trimmers and lawn edge trimmers; – machines equipped with metallic cutting accessories consisting of more than one piece, e.g. pivoting chains or flail blades; – edgers with rigid and/or metallic cutting devices. NOTE 101 Freely pivoting non-metallic cutting elements are considered not to be rigid cutting devices. NOTE 102 Edgers with rigid or metal cutting devices will be covered by a future part of IEC 62841-4. NOTE 103 Annex EE provides an informative summary of characteristics for lawn trimmers, lawn edge trimmers, grass trimmers, brush cutters and brush saws. Brush cutters and brush saws covered by this document are designed only to be operated with the machine to the right of the operator.
Edition
Not found
Published Date
2026-10-06
Status
Not found
Pages
160
Format 
Secure PDF
Secure – PDF details
- Save your file locally or view it via a web viewer
- Viewing permissions are restricted exclusively to the purchaser
- Device limits - 3
- Printing – Enabled only to print (1) copy
See more about our Environmental Commitment
Abstract
Preface This is the harmonized CSA Group and ULSE standard for Electric Motor-Operated Hand-Held Tools, Transportable Tools and Lawn and Garden Machinery – Safety – Part 4-4: Particular Requirements for Lawn Trimmers, Lawn Edge Trimmers, Grass Trimmers, Brush Cutters and Brush Saws. It is the First edition of CSA C22.2 No. 62841-4-4, and the First edition of UL 62841-4-4. This harmonized standard has been jointly revised on August 2, 2024. For this purpose, CSA Group and ULSE are issuing revision pages dated August 2, 2024. This harmonized standard is based on IEC Publication 62841-4-4: First edition, Electric Motor-Operated Hand-Held Tools, Transportable Tools and Lawn and Garden Machinery – Safety – Part 4-4: Particular Requirements for Lawn Trimmers, Lawn Edge Trimmers, Grass Trimmers, Brush Cutters and Brush Saws issued November 2020. IEC publication 62841-4-4 is copyrighted by the IEC. This harmonized standard was prepared by CSA Group and ULSE. The efforts and support of the International Harmonization Committee (IHC) for the adoption of the IEC series of Standards for Hand-Held, Motor-Operated, and Transportable Tools and Lawn and Garden Machinery UL are gratefully acknowledged. This standard is considered suitable for use for conformity assessment within the stated scope of the standard. This standard was reviewed by the CSA Subcommittee on Safety of Hand-Held Motor-Operated Electric Tools, under the jurisdiction of the CSA Technical Committee on Consumer and Commercial Products and the CSA Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the CSA Technical Committee. This standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group. Scope This clause of Part 1 is applicable, except as follows: Addition: This document applies to hand-held and walk-behind lawn trimmers and lawn edge trimmers, used by a standing operator for cutting grass, weeds or similar soft vegetation, and grass trimmers, brush cutters and brush saws used by a standing operator for cutting grass, weeds, brush, bushes, saplings and similar vegetation. This document does not apply to – hand-held machines having a mass of 18 kg or greater; – self-propelled lawn trimmers or lawn edge trimmers; – scissors type lawn trimmers and lawn edge trimmers; – machines equipped with metallic cutting accessories consisting of more than one piece, e.g. pivoting chains or flail blades; – edgers with rigid and/or metallic cutting devices. NOTE 101 Freely pivoting non-metallic cutting elements are considered not to be rigid cutting devices. NOTE 102 Edgers with rigid or metal cutting devices will be covered by a future part of IEC 62841-4. NOTE 103 Annex EE provides an informative summary of characteristics for lawn trimmers, lawn edge trimmers, grass trimmers, brush cutters and brush saws. Brush cutters and brush saws covered by this document are designed only to be operated with the machine to the right of the operator.
Previous Editions
Can’t find what you are looking for?
Please contact us at:
Related Documents
-

CSA E61951-2:21 (R2026) – Secondary cells and batteries containing alkaline or other non-acid electrolytes — Secondary sealed cells and batteries for portable applications — Part 2: Nickel-metal hydride (Adopted IEC 61951-2:2017, fourth edition, 2017-03, with Canadian deviations) | Accumulateurs alcalins et autres accumulateurs à électrolyte non acide — Accumulateurs étanches pour applications portables — Partie 2 : Nickel-métal hydrure (norme IEC 61951-2:2017 adoptée, quatrième édition, 2017-03, avec exigences propres au Canada)
CDN $527.00 Add to cart -

IEEE 844.4-2019/CSA C293.4:19 (R2024) – Impedance heating of pipelines and equipment—Application guide for design, installation, testing, commissioning, and maintenance
CDN $174.00 Add to cart -

CSA E61558-2-5:25 – Safety of transformers, reactors, power supply units and combinations thereof — Part 2-5: Particular requirements and tests for transformers for shavers, power supply units for shavers and shaver supply units (Adopted IEC 61558-2-5:2024, third edition, 2024-08, with Canadian deviations) | Sécurité des transformateurs, bobines d’inductance, blocs d’alimentation et combinaisons de ces éléments — Partie 2-5 : Exigences particulières et essais pour les transformateurs pour rasoirs, les blocs d’alimentation incorporant un transformateur pour rasoir et les blocs d’alimentation pour rasoirs (norme IEC 61558-2-5:2024 adoptée, troisième édition, 2024-08, avec exigences propres au Canada)
CDN $299.00 Add to cart -

CSA E61959:14 (R2024) – Secondary cells and batteries containing alkaline or other non-acid electrolytes – Mechanical tests for sealed portable secondary cells and batteries (Adopted IEC 61959:2004, first edition, 2004-01, with Canadian deviations) | Accumulateurs alcalins et autres accumulateurs à électrolyte non acide – Essais mécaniques pour accumulateurs portables étanches (norme CEI 61959:2004 adoptée, première édition, 2004-01, avec exigences propres au Canada)
CDN $56.00 Add to cart







