
CAN/CSA-C22.2 NO. 60745-1-07 (R2022)
CAN/CSA-C22.2 NO. 60745-1-07 (R2022) – Hand-held motor-operated electric tools – Safety – Part 1: General requirements (Binational standard with UL 60745-1)
CDN $496.00
Hand-held motor-operated electric tools – Safety – Part 1: General requirements (Binational standard with UL 60745-1)
Description
Preface This is the harmonized CSA Group and ULSE standard for Hand-Held Motor-Operated Electric Tools – Safety – Part 1: General Requirements. It is the third edition of CAN/CSA-C22.2 No. 60745-1, and the fourth edition of UL 60745-1. This harmonized standard has been jointly revised on October 25, 2024. For this purpose, CSA Group and ULSE are issuing revision pages dated October 25, 2024. This harmonized standard is based on IEC Publication 60745-1: fourth edition Hand-Held Motor-Operated Electric Tools — Safety — Part 1: General Requirements, issued April 2006. IEC 60745-1 is copyrighted by the IEC. This harmonized standard was prepared by CSA Group and ULSE. (UL). This standard is considered suitable for use for conformity assessment within the stated scope of the standard. This standard was reviewed by the CSA Subcommittee on Safety of Hand-Held Motor-Operated Electric Tools, under the jurisdiction of the CSA Technical Committee on Consumer and Commercial Products and the CSA Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the CSA Technical Committee. This standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group. Scope This part of IEC 60745 deals with the safety of hand-held motor-operated or magnetically driven electric tools, the rated voltage of the tools being not more than 250 V for single-phase a.c. or d.c. tools, and 440 V for three-phase a.c. tools. So far as is practicable, this standard deals with the common hazards presented by hand-held tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Tools with an electric heating element are within the scope of this standard. They should also comply with relevant parts of IEC 60335. Requirements for motors not isolated from the supply, and having basic insulation not designed for the rated voltage of the tools, are given in Annex B. Requirements for rechargeable battery powered motor-operated or magnetically driven tools and the battery packs for such tools are given in Annex K. Those for such tools that are also operated and/or charged directly from the mains or a non-isolated source are given in Annex L. Hand-held electric tools, hereinafter referred to as tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard. Requirements for such supports or working stands are given in Annex M. This standard does not apply to: – hand-held tools intended to be used in the presence of explosive atmosphere (dust, vapour or gas); – hand-held tools used for preparing and processing food; – hand-held tools for medical purposes (IEC 60601); – heating tools which are covered by IEC 60335-2-45. For hand-held tools intended to be used in vehicles or on board ships or aircraft, additional requirements may be necessary. For hand-held tools intended to be used in tropical countries, special requirements may be necessary. NOTE Attention is drawn to the fact that in many countries, additional requirements are specified by the national health authorities, the national authorities responsible for the protection of labour, the national water supply authorities, etc.
Edition
Not found
Published Date
2026-10-05
Status
Not found
Pages
231
Format 
Secure PDF
Secure – PDF details
- Save your file locally or view it via a web viewer
- Viewing permissions are restricted exclusively to the purchaser
- Device limits - 3
- Printing – Enabled only to print (1) copy
See more about our Environmental Commitment
Abstract
Preface This is the harmonized CSA Group and ULSE standard for Hand-Held Motor-Operated Electric Tools - Safety – Part 1: General Requirements. It is the third edition of CAN/CSA-C22.2 No. 60745-1, and the fourth edition of UL 60745-1. This harmonized standard has been jointly revised on October 25, 2024. For this purpose, CSA Group and ULSE are issuing revision pages dated October 25, 2024. This harmonized standard is based on IEC Publication 60745-1: fourth edition Hand-Held Motor-Operated Electric Tools — Safety — Part 1: General Requirements, issued April 2006. IEC 60745-1 is copyrighted by the IEC. This harmonized standard was prepared by CSA Group and ULSE. (UL). This standard is considered suitable for use for conformity assessment within the stated scope of the standard. This standard was reviewed by the CSA Subcommittee on Safety of Hand-Held Motor-Operated Electric Tools, under the jurisdiction of the CSA Technical Committee on Consumer and Commercial Products and the CSA Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the CSA Technical Committee. This standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group. Scope This part of IEC 60745 deals with the safety of hand-held motor-operated or magnetically driven electric tools, the rated voltage of the tools being not more than 250 V for single-phase a.c. or d.c. tools, and 440 V for three-phase a.c. tools. So far as is practicable, this standard deals with the common hazards presented by hand-held tools which are encountered by all persons in the normal use and reasonably foreseeable misuse of the tools. Tools with an electric heating element are within the scope of this standard. They should also comply with relevant parts of IEC 60335. Requirements for motors not isolated from the supply, and having basic insulation not designed for the rated voltage of the tools, are given in Annex B. Requirements for rechargeable battery powered motor-operated or magnetically driven tools and the battery packs for such tools are given in Annex K. Those for such tools that are also operated and/or charged directly from the mains or a non-isolated source are given in Annex L. Hand-held electric tools, hereinafter referred to as tools, which can be mounted on a support or working stand for use as fixed tools without any alteration of the tool itself, are within the scope of this standard. Requirements for such supports or working stands are given in Annex M. This standard does not apply to: - hand-held tools intended to be used in the presence of explosive atmosphere (dust, vapour or gas); - hand-held tools used for preparing and processing food; - hand-held tools for medical purposes (IEC 60601); - heating tools which are covered by IEC 60335-2-45. For hand-held tools intended to be used in vehicles or on board ships or aircraft, additional requirements may be necessary. For hand-held tools intended to be used in tropical countries, special requirements may be necessary. NOTE Attention is drawn to the fact that in many countries, additional requirements are specified by the national health authorities, the national authorities responsible for the protection of labour, the national water supply authorities, etc.
Previous Editions
Can’t find what you are looking for?
Please contact us at:
Related Documents
-

IEEE 844.3-2019/CSA C22.2 NO. 293.3:19 (R2024) – Impedance heating of pipelines and equipment—General, testing, marking, and documentation requirements
CDN $174.00 Add to cart -

CSA E60825-1:15 (R2025) – Safety of laser products — Part 1: Equipment classification and requirements (Adopted IEC 60825-1:2014, third edition, 2014-05, with Canadian deviations) | Sécurité des appareils à laser — Partie 1 : Classification des matériels et exigences (norme IEC 60825-1:2014 adoptée, troisième édition, 2014-05, avec exigences propres au Canada)
CDN $488.00 Add to cart -

CSA E61558-2-13:25 – Safety of transformers, reactors, power supply units and combinations thereof — Part 2-13: Particular requirements and tests for auto-transformers and power supply units incorporating auto-transformers for general applications (Adopted IEC 61558-2-13:2022, third edition, 2022-10, with Canadian deviations) | Sécurité des transformateurs, bobines d’inductance, blocs d’alimentation et combinaisons de ces éléments — Partie 2-13 : Exigences particulières et essais pour les autotransformateurs et les blocs d’alimentation qui incorporent des autotransformateurs pour applications d’ordre général (norme IEC 61558-2-13:2022 adoptée, troisième édition, 2022-10, avec exigences propres au Canada)
CDN $205.00 Add to cart -

CSA E61951-2:21 (R2026) – Secondary cells and batteries containing alkaline or other non-acid electrolytes — Secondary sealed cells and batteries for portable applications — Part 2: Nickel-metal hydride (Adopted IEC 61951-2:2017, fourth edition, 2017-03, with Canadian deviations) | Accumulateurs alcalins et autres accumulateurs à électrolyte non acide — Accumulateurs étanches pour applications portables — Partie 2 : Nickel-métal hydrure (norme IEC 61951-2:2017 adoptée, quatrième édition, 2017-03, avec exigences propres au Canada)
CDN $527.00 Add to cart







