
CAN/CSA-C22.2 NO. 62841-3-13:18 (R2023)
CAN/CSA-C22.2 NO. 62841-3-13:18 (R2023) – Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery – Safety – Part 3-13: Particular requirements for transportable drills (Binational standard with UL 62841-3-13)
CDN $315.00
Electric motor-operated hand-held tools, transportable tools and lawn and garden machinery – Safety – Part 3-13: Particular requirements for transportable drills (Binational standard with UL 62841-3-13)
Description
Preface This is the harmonized CSA Group and UL Standard For Electric Motor-Operated Hand-Held Tools, Transportable Tools And Lawn And Garden Machinery – Safety – Part 3-13: Particular Requirements for Transportable Drills . It is the First edition of CAN/CSA-C22.2 No. 62841-3-13 and the First edition of UL 62841-3-13. This harmonized standard is based on IEC Publication 62841-3-13: First edition Electric Motor-Operated Hand-Held Tools, Transportable Tools And Lawn And Garden Machinery – Safety – Part 3-13: Particular Requirements for Transportable Drills, issued February 2017. IEC 62841- 3-13 is copyrighted by the IEC. This harmonized standard was prepared by CSA Group and Underwriters Laboratories Inc. (UL). The efforts and support of the International Harmonization Committee (IHC) for the adoption of the IEC series of standards for Hand-Held, Motor-Operated, and Transportable Tools and Lawn and Garden Machinery UL are gratefully acknowledged. This standard is considered suitable for use for conformity assessment within the stated scope of the standard. This standard was reviewed by the CSA Subcommittee on Safety of Hand-Held Motor-Operated Electric Tools, under the jurisdiction of the CSA Technical Committee on Consumer and Commercial Products and the CSA Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the CSA Technical Committee. This standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group. This standard has been approved by the American National Standards Institute (ANSI) as an American National Standard. Scope This clause of Part 1 is applicable, except as follows: Addition: This part of IEC 62841 applies to transportable drills, with manually fed axial movement of the spindle, having a maximum chuck capacity of 13 mm. NOTE 101 Transportable drills are also known as bench drills or drill presses. This part of IEC 62841 does not apply to stationary drilling machines. This part of IEC 62841 does not apply to radial arm drills. This part of IEC 62841 does not apply to magnetic drill stands and drill motors. NOTE 102 Magnetic drill stands and drill motors will be covered by a future part of IEC 62841-3. NOTE 103 In Europe (EN 62841-3-13), the following conditions apply: Radial arm drills and stationary drilling machines are covered by EN 12717.
Edition
Not found
Published Date
2026-10-06
Status
Not found
Pages
36
Format 
Secure PDF
Secure – PDF details
- Save your file locally or view it via a web viewer
- Viewing permissions are restricted exclusively to the purchaser
- Device limits - 3
- Printing – Enabled only to print (1) copy
See more about our Environmental Commitment
Abstract
Preface This is the harmonized CSA Group and UL Standard For Electric Motor-Operated Hand-Held Tools, Transportable Tools And Lawn And Garden Machinery – Safety – Part 3-13: Particular Requirements for Transportable Drills . It is the First edition of CAN/CSA-C22.2 No. 62841-3-13 and the First edition of UL 62841-3-13. This harmonized standard is based on IEC Publication 62841-3-13: First edition Electric Motor-Operated Hand-Held Tools, Transportable Tools And Lawn And Garden Machinery – Safety – Part 3-13: Particular Requirements for Transportable Drills, issued February 2017. IEC 62841- 3-13 is copyrighted by the IEC. This harmonized standard was prepared by CSA Group and Underwriters Laboratories Inc. (UL). The efforts and support of the International Harmonization Committee (IHC) for the adoption of the IEC series of standards for Hand-Held, Motor-Operated, and Transportable Tools and Lawn and Garden Machinery UL are gratefully acknowledged. This standard is considered suitable for use for conformity assessment within the stated scope of the standard. This standard was reviewed by the CSA Subcommittee on Safety of Hand-Held Motor-Operated Electric Tools, under the jurisdiction of the CSA Technical Committee on Consumer and Commercial Products and the CSA Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the CSA Technical Committee. This standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group. This standard has been approved by the American National Standards Institute (ANSI) as an American National Standard. Scope This clause of Part 1 is applicable, except as follows: Addition: This part of IEC 62841 applies to transportable drills, with manually fed axial movement of the spindle, having a maximum chuck capacity of 13 mm. NOTE 101 Transportable drills are also known as bench drills or drill presses. This part of IEC 62841 does not apply to stationary drilling machines. This part of IEC 62841 does not apply to radial arm drills. This part of IEC 62841 does not apply to magnetic drill stands and drill motors. NOTE 102 Magnetic drill stands and drill motors will be covered by a future part of IEC 62841-3. NOTE 103 In Europe (EN 62841-3-13), the following conditions apply: Radial arm drills and stationary drilling machines are covered by EN 12717.
Previous Editions
Can’t find what you are looking for?
Please contact us at:
Related Documents
-

CAN/CSA-E60730-2-9:18 (R2023) – Automatic electrical controls — Part 2-9: Particular requirements for temperature sensing controls (Adopted IEC 60730-2-9:2018, edition 4:2015 consolidated with amendment 1:2018, with Canadian deviations)
CDN $944.00 Add to cart -

CSA E61951-2:21 (R2026) – Secondary cells and batteries containing alkaline or other non-acid electrolytes — Secondary sealed cells and batteries for portable applications — Part 2: Nickel-metal hydride (Adopted IEC 61951-2:2017, fourth edition, 2017-03, with Canadian deviations) | Accumulateurs alcalins et autres accumulateurs à électrolyte non acide — Accumulateurs étanches pour applications portables — Partie 2 : Nickel-métal hydrure (norme IEC 61951-2:2017 adoptée, quatrième édition, 2017-03, avec exigences propres au Canada)
CDN $527.00 Add to cart -

CSA E61959:14 (R2024) – Secondary cells and batteries containing alkaline or other non-acid electrolytes – Mechanical tests for sealed portable secondary cells and batteries (Adopted IEC 61959:2004, first edition, 2004-01, with Canadian deviations) | Accumulateurs alcalins et autres accumulateurs à électrolyte non acide – Essais mécaniques pour accumulateurs portables étanches (norme CEI 61959:2004 adoptée, première édition, 2004-01, avec exigences propres au Canada)
CDN $56.00 Add to cart -

IEEE 844.2-2017/CSA C293.2:17 (R2022) – Skin effect trace heating of pipelines, vessels, equipment, and structures—Application guide for design, installation, testing, commissioning, and maintenance
CDN $158.00 Add to cart







