
CSA/ANSI C22.2 NO. 19085-6:21 (R2025)
CSA/ANSI C22.2 NO. 19085-6:21 (R2025) – Woodworking machines — Safety — Part 6: Single spindle vertical moulding machines (“toupies”) (Adopted ISO 19085-6:2017, first edition, 2017-11, with North American deviations)
CDN $408.00
Woodworking machines — Safety — Part 6: Single spindle vertical moulding machines (“toupies”) (Adopted ISO 19085-6:2017, first edition, 2017-11, with North American deviations)
Description
CSA Preface This is the first edition of CSA/ANSI C22.2 No. 19085-6, Woodworking machines — Safety — Part 6: Single spindle vertical moulding machines (“toupies”) , which is an adoption, with North American deviations, of the identically titled ISO (International Organization for Standardization) Standard 19085-6 (first edition, 2017-11). It is one in a series of Standards issued by CSA Group under Part II of the Canadian Electrical Code. This Standard covers the safety requirements and measures for stationary and displaceable hand-fed single spindle vertical moulding machines. The North American deviations are intended to meet product requirements and to align with the Canadian Electrical Code, Part I (Canada) and the National Electrical Code (United States). This Standard is intended to be used in conjunction with CSA/ANSI C22.2 No. 19085-1:19, Woodworking machines — Safety — Part 1: Common requirements (adopted ISO 19085-1:2017, with North American deviations). This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group. This Standard has been approved by the American National Standards Institute (ANSI) as an American National Standard. Scope This document gives the safety requirements and measures for stationary and displaceable hand-fed single spindle vertical moulding machines, hereinafter referred to as “machines”, designed to cut wood and materials with similar physical characteristics to wood. NOTE 1 For the definitions of stationary and displaceable machines, see ISO 19085-1:2017, 3.4 and 3.5. It deals with all significant hazards, hazardous situations and events as listed in Clause 4, relevant to the machines when they are operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases are taken into account. NOTE 2 For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010. It is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with: a) device for the arbor to be vertically adjustable relative to the table; b) device to tilt the arbor; c) device to fit a manually operated tenoning sliding table; d) glass bead saw unit; e) adjustable table insert; f) device for changing the direction of rotation of the spindle; g) device for fixing shank mounted tools on the arbor; h) interchangeable arbor; i) quick tool/arbor change system; j) demountable power feed unit; k) support for the demountable power feed unit with power driven adjustments. This document does not apply to 1) machines equipped with outboard bearings, 2) machines equipped with powered movements of a front extension table and/or a tenoning sliding table, and 3) machines with an intended maximum tool diameter of less than or equal to 180 mm. NOTE 3 Hand-held motor-operated electric tools are dealt with in IEC 60745-1 together with IEC 60745-2-17. NOTE 4 Transportable motor-operated electric tools are dealt with in IEC 61029-1:1990, IEC 61029-2-8:1995/AMD1:1999 and IEC 61029-2-8:1995/AMD2:2001 This document is not applicable to machines intended for use in potentially explosive atmospheres or to machines manufactured prior to the date of its publication. 1DV Modify Clause 1 by adding the following to the first paragraph: This Standard applies to single spindle vertical moulding machines that are intended to be installed and used in accordance with the National Electrical Code (NFPA 70) in the United States and the Canadian Electrical Code, Part I (CSA C22.1) in Canada. In Canada, general requirements applicable to these machines are provided in CSA C22.2 No. 0.
Edition
Not found
Published Date
2026-10-06
Status
Not found
Pages
74
Format 
Secure PDF
Secure – PDF details
- Save your file locally or view it via a web viewer
- Viewing permissions are restricted exclusively to the purchaser
- Device limits - 3
- Printing – Enabled only to print (1) copy
See more about our Environmental Commitment
Abstract
CSA Preface This is the first edition of CSA/ANSI C22.2 No. 19085-6, Woodworking machines — Safety — Part 6: Single spindle vertical moulding machines ("toupies") , which is an adoption, with North American deviations, of the identically titled ISO (International Organization for Standardization) Standard 19085-6 (first edition, 2017-11). It is one in a series of Standards issued by CSA Group under Part II of the Canadian Electrical Code. This Standard covers the safety requirements and measures for stationary and displaceable hand-fed single spindle vertical moulding machines. The North American deviations are intended to meet product requirements and to align with the Canadian Electrical Code, Part I (Canada) and the National Electrical Code (United States). This Standard is intended to be used in conjunction with CSA/ANSI C22.2 No. 19085-1:19, Woodworking machines — Safety — Part 1: Common requirements (adopted ISO 19085-1:2017, with North American deviations). This Standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group. This Standard has been approved by the American National Standards Institute (ANSI) as an American National Standard. Scope This document gives the safety requirements and measures for stationary and displaceable hand-fed single spindle vertical moulding machines, hereinafter referred to as "machines", designed to cut wood and materials with similar physical characteristics to wood. NOTE 1 For the definitions of stationary and displaceable machines, see ISO 19085-1:2017, 3.4 and 3.5. It deals with all significant hazards, hazardous situations and events as listed in Clause 4, relevant to the machines when they are operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases are taken into account. NOTE 2 For relevant but not significant hazards, e.g. sharp edges of the machine frame, see ISO 12100:2010. It is also applicable to machines fitted with one or more of the following devices/additional working units, whose hazards have been dealt with: a) device for the arbor to be vertically adjustable relative to the table; b) device to tilt the arbor; c) device to fit a manually operated tenoning sliding table; d) glass bead saw unit; e) adjustable table insert; f) device for changing the direction of rotation of the spindle; g) device for fixing shank mounted tools on the arbor; h) interchangeable arbor; i) quick tool/arbor change system; j) demountable power feed unit; k) support for the demountable power feed unit with power driven adjustments. This document does not apply to 1) machines equipped with outboard bearings, 2) machines equipped with powered movements of a front extension table and/or a tenoning sliding table, and 3) machines with an intended maximum tool diameter of less than or equal to 180 mm. NOTE 3 Hand-held motor-operated electric tools are dealt with in IEC 60745-1 together with IEC 60745-2-17. NOTE 4 Transportable motor-operated electric tools are dealt with in IEC 61029-1:1990, IEC 61029-2-8:1995/AMD1:1999 and IEC 61029-2-8:1995/AMD2:2001 This document is not applicable to machines intended for use in potentially explosive atmospheres or to machines manufactured prior to the date of its publication. 1DV Modify Clause 1 by adding the following to the first paragraph: This Standard applies to single spindle vertical moulding machines that are intended to be installed and used in accordance with the National Electrical Code (NFPA 70) in the United States and the Canadian Electrical Code, Part I (CSA C22.1) in Canada. In Canada, general requirements applicable to these machines are provided in CSA C22.2 No. 0.
Previous Editions
Can’t find what you are looking for?
Please contact us at:
Related Documents
-

CAN/CSA-E61558-1:12 (R2022) – Safety of power transformers, power supplies, reactors and similar products – Part 1: General requirements and tests (Adopted IEC 61558- 1:1997 + A1:1998, edition 2.1, 2009-04 with Canadian deviations) | Sécurité des transformateurs, alimentations, bobines d’inductance et produits analogues – Partie 1: Exigences générales et essais (norme CEI 61558-1:1997 + A1:1998 adoptée, édition 2.1, 2009-04 avec exigences propres au Canada)
CDN $630.00 Add to cart -

CSA E61951-2:21 (R2026) – Secondary cells and batteries containing alkaline or other non-acid electrolytes — Secondary sealed cells and batteries for portable applications — Part 2: Nickel-metal hydride (Adopted IEC 61951-2:2017, fourth edition, 2017-03, with Canadian deviations) | Accumulateurs alcalins et autres accumulateurs à électrolyte non acide — Accumulateurs étanches pour applications portables — Partie 2 : Nickel-métal hydrure (norme IEC 61951-2:2017 adoptée, quatrième édition, 2017-03, avec exigences propres au Canada)
CDN $527.00 Add to cart -

IEEE 844.3-2019/CSA C22.2 NO. 293.3:19 (R2024) – Impedance heating of pipelines and equipment—General, testing, marking, and documentation requirements
CDN $174.00 Add to cart -

CSA E61951-1:21 (R2026) – Secondary cells and batteries containing alkaline or other non-acid electrolytes — Secondary sealed cells and batteries for portable applications — Part 1: Nickel-cadmium (Adopted IEC 61951:2017, fourth edition, 2017-03, with Canadian deviations) | Accumulateurs alcalins et autres accumulateurs à électrolyte non acide — Accumulateurs étanches pour applications portables — Partie 1 : Nickel-cadmium (norme IEC 61951-1:2017 adoptée, quatrième édition, 2017-03), avec exigences propres au Canada)
CDN $527.00 Add to cart







