
CSA C22.2 NO. 60974-1:19 (R2024)
CSA C22.2 NO. 60974-1:19 (R2024) – Arc welding equipment – Part 1: Welding power sources (Trinational standard with NMX-J-038-1-ANCE-2019; Section 1 and ANSI/NEMA/IEC 60974-1-2019)
CDN $661.00
Arc welding equipment – Part 1: Welding power sources (Trinational standard with NMX-J-038-1-ANCE-2019; Section 1 and ANSI/NEMA/IEC 60974-1-2019)
Description
Preface This is the harmonized ANCE, CSA Group, and NEMA standard for Arc Welding Equipment — Part 1: Welding Power Sources . It is the first edition of NMX-J-038-1-ANCE; Section 1, the first edition of CSA C22.2 No. 60974-1, and the second edition of ANSI/NEMA/IEC 60974-1. This edition of CSA C22.2 No. 60974-1 replaces CAN/CSA-E60974-1:12 (adopted IEC 60974-1:2012) and CSA C22.2 No. 60-M1990. This harmonized standard is based on IEC publication 60974-1: fifth edition, Arc welding equipment — Part 1: Welding power sources, issued February 2017. IEC 60974-1 is copyrighted by the IEC. This harmonized standard was prepared by the Association of Standardization and Certification (ANCE), CSA Group, and the National Electrical Manufacturers Association (NEMA). The efforts and support of Industry Associations [Cámara Nacional de Manufacturas Eléctricas (CANAME)], and of the Technical Harmonization Committee (THC 26) of the Council on the Harmonization of Electrotechnical Standards of the Nations of the Americas (CANENA), are gratefully acknowledged. This standard is considered suitable for use for conformity assessment within the stated scope of the standard. This standard was reviewed by the Standardization Committee of the Association of Standardization and Certification, A. C., CONANCE, committee integrated based on the terms of the Federal Law on Metrology and Standardization for developing, approving, and reviewing Mexican Standards, in the framework of the principles of representativeness, balance, and consensus. In accordance with the CONANCE operative procedure, the consensus is the general agreement, characterized by the absence of opposition based on relevant aspects by any party directly affected, after a process of analysis to consider the points of view of all parties involved and conflicting arguments reconciliation. This standard was reviewed by the CSA Subcommittee on Arc Welding Equipment, under the jurisdiction of the CSA Technical Committee on Industrial Products and the CSA Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the CSA Technical Committee. In Canada, for general information on the Standards of the Canadian Electrical Code, Part II, see the preface of CAN/CSA-C22.2 No. 0. This standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group. This Standard has been approved by the American National Standards Institute (ANSI) as an American National Standard. This American National Standard is an adoption of IEC 60974-1 edition 5, Arc Welding Equipment — Part 1: Welding Power Sources, and was developed and approved in accordance with procedures set forth by the American National Standards Institute. Scope This part of IEC 60974 is applicable to power sources for arc welding and allied processes designed for industrial and professional use, and supplied by a voltage not exceeding 1 000 V, battery supplied or driven by mechanical means. This document specifies safety and performance requirements of welding power sources and plasma cutting systems. This document is not applicable to limited duty arc welding and cutting power sources which are designed mainly for use by laymen and designed in accordance with IEC 60974-6. 1DV.1 D2 Modify Clause 1 by replacing the third paragraph with the following: Welding equipment that has been designed to comply with this standard and is intended for industrial and professional use, and that meets all the scope limitations of the trinational adoption of IEC 60974-6 is suitable for use by laypersons provided the additional instructions and markings requirements of the trinational adoption of IEC 60974-6 are met. 1DV.2 DR Modification to Clause 1 by adding the following: This equipment is intended for installation in accordance with the national installation codes for use in ordinary locations. See Annex DVA, Table DVA.3, Ref. No. 1. This document includes requirements for battery-powered welding power sources and battery packs, which are given in Annex O. This document is not applicable to testing of power sources during periodic maintenance or after repair. NOTE 1 Typical allied processes are electric arc cutting and arc spraying. NOTE 2 AC systems having a nominal voltage between 100 V and 1 000 V are given in Table 1 of IEC 60038:2009. NOTE 3 This document does not include electromagnetic compatibility (EMC) requirements. 1DV.3 D2 Modification to Clause 1 by adding the following: In Canada, products covered by the scope of this Standard are also subject to the requirements of Annex DVA, Table DVA.3, Ref. No. 15.
Edition
Not found
Published Date
2026-10-06
Status
Not found
Pages
Not found
Format 
Secure PDF
Secure – PDF details
- Save your file locally or view it via a web viewer
- Viewing permissions are restricted exclusively to the purchaser
- Device limits - 3
- Printing – Enabled only to print (1) copy
See more about our Environmental Commitment
Abstract
Preface This is the harmonized ANCE, CSA Group, and NEMA standard for Arc Welding Equipment — Part 1: Welding Power Sources . It is the first edition of NMX-J-038-1-ANCE; Section 1, the first edition of CSA C22.2 No. 60974-1, and the second edition of ANSI/NEMA/IEC 60974-1. This edition of CSA C22.2 No. 60974-1 replaces CAN/CSA-E60974-1:12 (adopted IEC 60974-1:2012) and CSA C22.2 No. 60-M1990. This harmonized standard is based on IEC publication 60974-1: fifth edition, Arc welding equipment — Part 1: Welding power sources, issued February 2017. IEC 60974-1 is copyrighted by the IEC. This harmonized standard was prepared by the Association of Standardization and Certification (ANCE), CSA Group, and the National Electrical Manufacturers Association (NEMA). The efforts and support of Industry Associations [Cámara Nacional de Manufacturas Eléctricas (CANAME)], and of the Technical Harmonization Committee (THC 26) of the Council on the Harmonization of Electrotechnical Standards of the Nations of the Americas (CANENA), are gratefully acknowledged. This standard is considered suitable for use for conformity assessment within the stated scope of the standard. This standard was reviewed by the Standardization Committee of the Association of Standardization and Certification, A. C., CONANCE, committee integrated based on the terms of the Federal Law on Metrology and Standardization for developing, approving, and reviewing Mexican Standards, in the framework of the principles of representativeness, balance, and consensus. In accordance with the CONANCE operative procedure, the consensus is the general agreement, characterized by the absence of opposition based on relevant aspects by any party directly affected, after a process of analysis to consider the points of view of all parties involved and conflicting arguments reconciliation. This standard was reviewed by the CSA Subcommittee on Arc Welding Equipment, under the jurisdiction of the CSA Technical Committee on Industrial Products and the CSA Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the CSA Technical Committee. In Canada, for general information on the Standards of the Canadian Electrical Code, Part II, see the preface of CAN/CSA-C22.2 No. 0. This standard has been developed in compliance with Standards Council of Canada requirements for National Standards of Canada. It has been published as a National Standard of Canada by CSA Group. This Standard has been approved by the American National Standards Institute (ANSI) as an American National Standard. This American National Standard is an adoption of IEC 60974-1 edition 5, Arc Welding Equipment — Part 1: Welding Power Sources, and was developed and approved in accordance with procedures set forth by the American National Standards Institute. Scope This part of IEC 60974 is applicable to power sources for arc welding and allied processes designed for industrial and professional use, and supplied by a voltage not exceeding 1 000 V, battery supplied or driven by mechanical means. This document specifies safety and performance requirements of welding power sources and plasma cutting systems. This document is not applicable to limited duty arc welding and cutting power sources which are designed mainly for use by laymen and designed in accordance with IEC 60974-6. 1DV.1 D2 Modify Clause 1 by replacing the third paragraph with the following: Welding equipment that has been designed to comply with this standard and is intended for industrial and professional use, and that meets all the scope limitations of the trinational adoption of IEC 60974-6 is suitable for use by laypersons provided the additional instructions and markings requirements of the trinational adoption of IEC 60974-6 are met. 1DV.2 DR Modification to Clause 1 by adding the following: This equipment is intended for installation in accordance with the national installation codes for use in ordinary locations. See Annex DVA, Table DVA.3, Ref. No. 1. This document includes requirements for battery-powered welding power sources and battery packs, which are given in Annex O. This document is not applicable to testing of power sources during periodic maintenance or after repair. NOTE 1 Typical allied processes are electric arc cutting and arc spraying. NOTE 2 AC systems having a nominal voltage between 100 V and 1 000 V are given in Table 1 of IEC 60038:2009. NOTE 3 This document does not include electromagnetic compatibility (EMC) requirements. 1DV.3 D2 Modification to Clause 1 by adding the following: In Canada, products covered by the scope of this Standard are also subject to the requirements of Annex DVA, Table DVA.3, Ref. No. 15.
Previous Editions
Can’t find what you are looking for?
Please contact us at:
Related Documents
-

CSA E61347-2-3:23 – Lamp control gear — Part 2-3: Particular requirements for a.c. and/or d.c. supplied electronic control gear for fluorescent lamps (Adopted IEC 61347-2-3:2011, edition 2:2011 consolidated with amendment 1:2016, with Canadian deviations) | Appareillages de lampes — Partie 2-3 : Exigences particulières pour les appareillages électroniques alimentés en courant alternatif et/ou en courant continu pour lampes fluorescentes (norme IEC 61347-2-3:2011 adoptée, édition 2:2011 consolidée par l’amendement 1:2016, avec exigences propres au Canada)
CDN $620.00 Add to cart -

CSA E61951-2:21 (R2026) – Secondary cells and batteries containing alkaline or other non-acid electrolytes — Secondary sealed cells and batteries for portable applications — Part 2: Nickel-metal hydride (Adopted IEC 61951-2:2017, fourth edition, 2017-03, with Canadian deviations) | Accumulateurs alcalins et autres accumulateurs à électrolyte non acide — Accumulateurs étanches pour applications portables — Partie 2 : Nickel-métal hydrure (norme IEC 61951-2:2017 adoptée, quatrième édition, 2017-03, avec exigences propres au Canada)
CDN $527.00 Add to cart -

CSA E61347-1:24 – Lamp controlgear – Part 1: General and safety requirements (Adopted IEC 61347-1:2015, edition 3:2015 consolidated with amendment 1:2017, with Canadian deviations) | Appareillages de lampes – Partie 1 : Exigences générales et exigences de sécurité (norme IEC 61347-1:2015 adoptée, édition 3:2015 consolidée par l’amendement 1:2017), avec exigences propres au Canada)
CDN $907.00 Add to cart -

CAN/CSA-E60730-2-9:18 (R2023)/A2:24 – Amendment 2:2024 to CAN/CSA-E60730-2-9:18, Automatic electrical controls — Part 2-9: Particular requirements for temperature sensing controls (Adopted amendment 2:2020 to IEC 60730-2-9:2018)
CDN $19.00 Add to cart







